manualshive.com logo in svg

MasterCraft 062-3538-6, Instruction Manual, Page: 6 / 17

Share
Download
MasterCraft 062-3538-6 Instruction Manual Download Page 6

headline bars

continuation tabs

notes

warnings

headline bars

continuation tabs

notes

warnings

model no. 062-3538-6 | contact us 1-800-689-9928

6

TECHNICAL SPECIFICA

TIONS

TECHNICAL SPECIFICATIONS

Liquid temperature range

32 to 95°F (0 to 35°C)

Impeller

Plastic

Solids handling

1/4” (6.3 mm) spherical

Discharge size

1 1/2” (3.8 cm) female national pipe thread (FNPT) or   
1 1/4” (3.2 cm) FNPT (with adaptor)

Seal 

Lip seal

Cord length 

10’ (3 m)

Upper bearing

Ball bearing

Lower bearing

Ball bearing

Single phase

Permanent split capacitor (PSC)

Motor protection

Auto-reset thermal overload protection in motor

Construction material

Stainless steel motor housing, cast iron volute, plastic 
impeller

Motor

NEMA L, torque curve, oil-filled, squirrel cage induction, 
class B insulation

Maximum flow

4200 U.S. GPH (15,899 L/hr)

Maximum head height 

29’ (8.8 m)

MOTOR AND ELECTRICAL

SKU number

062-3538-6

HP

1/2

Power

115 V AC

Hz

60

RPM

3450

Full load amps

6.9

Cord size

18 AWG

Cord type

SJTW

NOTE:

Do not reduce size of discharge pipe or hose below 1 1/4” (3.2 cm) diameter.
If discharge is too small, pump will overheat and fail prematurely.
This pump is designed for use in a residential sump only. Only pump
water with this pump.

Summary of Contents for 062-3538-6


















Reviews:

No comments