manualshive.com logo in svg

MasterCraft 062-3538-6, Instruction Manual, Page: 16 / 17

Share
Download
MasterCraft 062-3538-6 Instruction Manual Download Page 16

headline bars

continuation tabs

notes

warnings

model no. 062-3538-6 | contact us 1-800-689-9928

16

TROUBLESHOOTING

Problem

Possible Causes 

Corrective Action

The pump does not
 start or run.

The fuse is blown.
The breaker is tripped.
The plug is disconnected.
The plug is corroded.
There is thermal overload.

The switch failed.
The motor failed. 

Replace the fuse.
Reset the breaker.
Secure the plug.
Clean the plug prongs.
Unplug for 30 minutes and then 
plug in again.
Replace the switch.
Replace the pump.

The pump operates 
but pumps little
or no water.

The screen is blocked.
Debris is caught in the 
impeller or discharge.
The impeller is loose on the 
shaft or the impeller is broken.

Clean the screen.
Remove the debris.

Reassemble the impeller or replace
the impeller.

The pump starts and 
stops too often.

There is a backflow of water 
from the piping or the check 
valve is leaking.
The float switch is stuck.

Install a check valve or replace the 
check valve.

Clean the float switch to make sure the 
float moves up and down freely.

The pump will not 
shut off.

The switch is tangled.

The float switch is faulty.
The float is obstructed.

Reposition the pump and make sure 
the switch moves freely.
Replace the switch.
Remove the obstruction.

TROUBLESHOO

TING

Summary of Contents for 062-3538-6


















Reviews:

No comments