background image

24

25

model no. 058-8195-2  |  contact us 1-800-689-9928

PARTS LIST

PARTS LIST

1

1

20

Cable holder

Ground cable and clamp

1

2

Wire feed setting knob

1

21

Back panel

1

3

Torch cable holder

1

22

Gas hose connector

1

4

Cable holder

1

23

Rectifier

1

5

Front panel

1

24

Rectifier bracket

1

6

PCB support

1

25

Vertical middle panel

1

7

PCB

1

26

Spool holder

1

8

Bottom

1

27

Plastic hinge

2

9

Feet

1

28

Left panel

1

10

Control transformer

4

29

Fuse

1

11

Thermal relay

1

30

Red terminal

1

12

Circuit breaker

1

31

Black terminal

1

13

Main transformer

1

32

Door bolt

1

14

Fan bracket 

1

33

Wire feeder

1

15

Fan

2

34

MIN/MAX 1/2 voltage switch

2

16

Fan blade

1

35

ON/OFF switch

1

17

Handle

1

36

Overload indicator

1

18

Right panel

1

37

MIG torch

1

19

Power cord

1

28

1

4

8

9

6

7

31

12

34

37

27

26

25

22

21

20

19

24

23

10

29

32

33

35

36

2

3

5

11

13

14

18

15

16

17

30

No.

No.

Description

Description

Qty.

Qty.

PARTS LIST

EXPLODED VIEW

If any part is missing or damaged, do not use the product until the missing or damaged part has been replaced.

WARNING!

NOTE:

The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the 
manufacturer nor distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs 
to the product, or that he or she is qualified to replace any parts of the product. In fact, the manufacturer and/or distributor expressly statesthat 
all repairs and parts replacements should be undertaken by certified and licensed technicians, and not by the buyer. The buyer assumes all risk 
and liability arising out of his or her repairs to the original product or replacement parts thereto, or arising out of his or her installation of 
replacement parts thereto.

model no. 058-1294-8  |  contact us 1-800-689-9928

model no. 058-1294-8  |  contact us 1-800-689-9928

model no. 058-1294-8  |  contact us 1-800-689-9928

model no. 058-8195-2  |  contact us 1-800-689-9928

Summary of Contents for 058-8195-2
















Reviews: