background image

26

27

model no. 058-8195-2   |  contact us 1-800-689-9928

YT

NA

RR

A

W

YT

NA

RR

A

W

3-Year Limited Warranty 

This Mastercraft product is guaranteed for a period of three (3) years from the date of original retail  
purchase, against defects in materials and workmanship.
Subject to the conditions and limitations described below, this product, if returned to us with proof 
of purchase within the stated warranty period and if covered under this warranty, will be repaired 
or replaced (with the same model, or one of equal value or specification), at our option. We will 
bear the cost of any repair or replacement and any costs of labour relating thereto.

These warranties are subject to the following conditions and limitations

a)  a bill of sale verifying the purchase and purchase date must be provided;

b)  this warranty will not apply to any product or part thereof which is worn or broken or which has 

become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper 

installation, operation or maintenance (as outlined in the applicable owner s manual or operating 

instructions) or which is being used for industrial, professional, commercial or rental purposes;
c)  this warranty will not apply to normal wear and tear or to expendable parts or accessories that 

may be supplied with the product which are expected to become inoperative or unusable after 

d)  this warranty will not apply to routine maintenance and consumable items such as, but not 

limited to, fuel, lubricants, vacuum bages, blades, belts, sandpaper, bits, fluids, tune-ups or 

e)  this warranty will not apply where damage is caused by repairs made or attempted by others 

(i.e. persons not authorized by the manufacturer);
f)   this warranty will not apply to any product that was sold to the original purchaser as a 

reconditioned or refurbished product (unless otherwise specified in writing);
g)  this warranty will not apply to any product or part thereof if any part from another manufacturer 

is installed therein or any repairs or alterations have been made or attempted by unauthorized persons; 
h)  this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited 

to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical 

i)   this warranty will not apply to component parts sold by and identified as the product of another 

company,  which shall  be covered under the product manufacturer s warranty, if any.

Additional Limitations

This warranty applies only to the original purchaser and may not be transferred. Neither the retailer nor 
the manufacturer shall be liable for any other expense, loss or damage, including, without limitation, any
indirect, incidental, consequential or exemplary damages arising in connection with the sale, use or inability 
to use this product.

This warranty gives you specific legal rights, and you may have other rights, which may vary from province 
to province. The provisions contained in this warranty are not intended to limit, modify, take away from,
disclaim or exclude any statutory warranties set forth in any applicable provincial or federal legislation.

Made in China
Imported by
Mastercraft Canada Toronto, Canada M4S 2B8

Notice to Consumer

model no. 058-1294-8  |  contact us 1-800-689-9928

model no. 058-1294-8  |  contact us 1-800-689-9928

model no. 058-1294-8  |  contact us 1-800-689-9928

model no. 058-8195-2  |  contact us 1-800-689-9928

a reasonable period of use; 

adjustment;

leaners; 

Summary of Contents for 058-8195-2
















Reviews: