Masimo SET Rad-57 Operator'S Manual Download Page 3 | Manualshive

Page: 3 / 73

background image

The Rad-57 Signal Extraction Pulse CO-Oximeter Operating Instructions intend to provide the necessary infor-
mation for proper operation of all Rad-57 Pulse CO-Oximeter models.
General knowledge of Pulse CO-Oximetry and an understanding of the features and functions of the Rad-57
Signal Extraction Pulse CO-Oximeter models are prerequisites for proper use.
Do not operate any of the Rad-57 Signal Extraction Pulse CO-Oximeter models without completely reading and
understanding these instructions.
NOTICE
Purchase or possession of this device does not carry any express or implied license to use with replacement
parts which would, alone or in combination with this device, fall within the scope of one of the relating patents.
CAUTION:

FEDERAL LAW (U.S.) RESTRICTS THIS DEVICE TO SALE BY OR ON THE ORDER OF A

PHYSICIAN.

For further information contact:
Masimo Corporation
40 Parker
Irvine, CA 92618
USA
Tel.: 949-297-7000
Fax.: 949-297-7001
www.masimo.com
EU Authorized Representative for Masimo Corporation:

MDSS GmbH

Schiffgraben 41

D-30175 Hannover, Germany

Covered by one or more of the following U.S patents: 5482036, 5490505, 5632272, 5685299, 5758644,

5769785, 5919134, 6002952, 6011986, 6067462, 6157850, 6229856, 6236872, 6263222, 6360114, 6388240,

6430525, 6463311, 6501975, 6515273, 6606511, 6643530, 6650917, 6654624, 6684090, 6699194, 6745060,

6816741, 6826419, 6850787, 6861639, 6979812, 7186966, 7215984, 7215986, 7221971, 7254433, 7295866,

7328053, 7373194, 7376453, 7377899, 7467002, 7469157, 7471969, 7489958, 7496393, 7499741, 7509154,

7530955, RE38476, RE38492, international equivalents, or one or more of the patents referenced at www.

masimo.com/patents.htm. Other patents pending.
© 2016 Masimo Corporation. Masimo, , SET, Rad, LNCS, LNOP, Signal IQ, Discrete Saturation Transform,

DST, Rainbow, SpCO,SpMet, and FastSat are registered trademarks of Masimo Corporation.
Rad-57, SIQ, LNOPv, Pulse CO-Oximeter and APOD are trademarks of Masimo Corporation.

EC REP

«
1
2
3
4
5
...
»

Summary of Contents for Rad-57










































































Reviews:

No comments

Related manuals for Rad-57

Brand: B&K Pages: 8

Brand: Zetec Pages: 23

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: Panta Safe Light Pages: 2

Brand: Calrec Pages: 70

Brand: Jet Pages: 12

VLR100 LED Series

Brand: WE-EF Pages: 3

Brand: Warner Electric Pages: 14

Brand: Milestone Pages: 64

Brand: BH FITNESS Pages: 24

Brand: Best Fitness Pages: 26

Brand: TRX Pages: 2

A/C Air Launcher 101050

Brand: CITC Pages: 10

Brand: Vision & Control Pages: 32

Brand: ADJ Pages: 6

Brand: BERRIDGE Pages: 11

Brand: Helmer Pages: 18

Brand: IDENTITES Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands