background image

      

- 28

MPL 206 A - MPL 226 A

GB

GB

7 ANOMALIES, CAUSES AND REMEDIES

On starting, the generator does not run and the starter motor does not emit any signal.
• Check that the thermal switch located on the start unit has not tripped.  Check battery connection.
• Check that the emergency stop button is off. If on, turn it to switch it off.

The starter motor turns but the main engine does not start.
• Check that there is fuel in the tank. Fill up.
• Check that the stop solenoid valve is powered. Consult Service Centre.
• Check fuel pump functioning. Consult Service Centre.

The generator switches off during the operating period.
• Check if there is fuel in the tank. Fill up.
• Check if the low oil level protection has been activated; check the level and if low, add the oil necessary to bring

it up to the correct level.  There are no warning lights; always carry out a visual inspection.

The engine runs irregularly.
• Check the fuel filter.  Replace it.
• Check fuel pump functioning. Consult Service Centre.
• Check the setting of the injectors.  Consult Service Centre.

There is high smoke emission from the exhaust.
• Check the air filter.  Clean its elements or, if necessary, replace them.
• Check that the oil level does not exceed the MAX notch.  Bring it down to the correct level.

Starter battery flat.
• Check the electrolyte level in the battery.  Fill up.
• Check the battery charging device.  Consult Service Centre.
• Check integrity of the battery.

The generator does not deliver power to the outlets but the voltmeter indicates that voltage is present.
• Check that the differential magnetothermal switch, or a magnetothermal switch, is in the ON position.

The generator does not deliver power to the outlets and the voltmeter does not indicate that voltage is
present.
• Likely alternator fault.  Consult a Service Centre.

7.1 H

OW

 

TO

 

ORDER

 

THE

 

SPARE

 

PARTS

In order to ensure a good functioning of the generator, we recommed to use original spare parts only.
The spares can be purchased from the ma

s

e authorized assistence network (consult the SERVICE manual

enclosed with the generator).
You can get any futher information contacting the ma

s

e central Service.

Summary of Contents for MPL 206 A

































Reviews: