background image

 

MAC 600/E

 

user manual

 

 

 

© 1997 - 2000  Martin Professional A/S, Denmark.

 

All rights reserved. No part of this manual may be 

reproduced, in any form or by any means, without 
permission in writing from Martin Professional A/S, 
Denmark.

 

Printed in Denmark.

 

P/N 35000018 Rev. G 

 

section 1

 

INTRODUCTION

 

About this manual .................................................................................................................................................... 4

 

Safety precautions ................................................................................................................................................... 4

 

section 2

 

SETUP

 

Unpacking................................................................................................................................................................ 5 

Installing or changing the lamp ................................................................................................................................ 5

 

Powering the fixture ................................................................................................................................................. 5

 

Summary of Contents for MAC 600





























Reviews: