Martin Audio Wavefront Precision Series User Manual Download Page 39

Page: 39 / 45

WPS USER GUIDE V1.0

WPS USER GUIDE

Carefully unpin the fifth cabinet from the fourth cabinet at the
rear by removing the LINK pin, be aware that the array may
swing when this is done.

Lift the array and allow it to swing on the front link. The lower
the array down so that the cart meets the floor.

Remove the front locking pins from the fifth cabinet at each
side. Ensure the cart is fully grounded when removing pins.

Lift the array so that the front links are floating. This makes it
easier to remove the linking pins from the fourth cabinet.

Remove the link pins from the fourth cabinet (the front links return to the transport position). Stow the pins and replace the poles and lid
ready for transportation.

Summary of Contents for Wavefront Precision Series












































Search results

Summary of Contents for Wavefront Precision Series

Reviews:

Related manuals for Wavefront Precision Series

Brands by name

Popular brands

Martin Audio Wavefront Precision Series, User Manual

Search results

Summary of Contents for Wavefront Precision Series

Reviews:

Related manuals for Wavefront Precision Series

Brands by name

Popular brands