Martin Audio Wavefront Precision Series User Manual Download Page 36 | Manualshive

Page: 36 / 45

background image

Copyright © 2019 Martin Audio Ltd.

36

WPS USER GUIDE V1.0

WPS USER GUIDE

Support the rear of the cart and remove the rear pin holding the
cart to the array.

Lower the back of the cart to the ground.

Repeat at the front of the array supporting the cart and removing the pins holding the cart to the array.

Raise the array to the final trim height. The use of either one or two motors and rigging positions (WPSGRIDt only) allows both negative
(down-tilt) or positive (up-tilt) array angles to be easily achieved.

«
...
34
35
36
37
38
...
»

Summary of Contents for Wavefront Precision Series














































Reviews:

No comments

Related manuals for Wavefront Precision Series

Interlogix 60-875 Simon

Brand: GE Pages: 40

Brand: GE Security Pages: 2

Brand: Samsung Pages: 36

Brand: Nacon Pages: 12

Brand: Gardi Systems Pages: 6

MME239 - Micro DVD Home Theater System

Brand: Magnavox Pages: 39

Brand: Fenton Pages: 16

Brand: M&S Systems Pages: 4

Brand: FingerTec Pages: 35

Brand: volkano Pages: 2

Brand: Pure Acoustics Pages: 1

Brand: Valcom Pages: 2

Brand: Hame Pages: 26

Brand: Altec Lansing Pages: 1

Microburst MB5000

Brand: Pinnacle Pages: 4

Brand: Anchor Pages: 1

ActiveEYE MS15A

Brand: X10 Pages: 2

MIG 270 Separate

Brand: Jasic Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands