34
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTIONS
ADV
ANCED
OPERA
TION
RESETTING THE CODE
1.
1.
2.
1.
Press and hold down the
SOURCE
button
for appliance which should be controlled and
press
SET
button until the SEND indicator
blinking twice.
Then back light fl ushes.
2.
Press the below codes to reset.
TV :
1000
DVD
:
2000
CD :
3000
DSS
:
4000
The indicator will blink twice.
Note:
After this procedure, the selected
SOURCE
button is
set initial code.
2.
Press and hold down the
SOURCE
button for
appliance which should be controlled and press
SET
button until the SEND indicator blinking
twice. Then back light fl ushes.
3.
Aim the remote control at the appliance and
slowly alternate between pressing
INPUT
3
button and the
SOURCE ON/OFF
button for the
appliance.
4.
Stop when the appliance turns off.
5.
Press
ENTER
button once to lock in the code.
CHECKING THE CODE
1.
2.
4.
3.
1.
1.
Press and hold down the
SOURCE
button for
appliance which should be controlled and press
SET
button until the SEND indicator blinking twice
then back light fl ushes.
2.
Press
the
INFO
button.
The SEND indicator will blink twice.
3.
To view the code for fi rst digit, press
1
once.
Wait 3 seconds, count the SEND indicator
blinks (e.g. 3 blinks = 3) and write down the
number.
Note:
If a code digit is “0”, the SEND indicator will not
blink.
4.
Repeat
step
3
three more times for remaining
digits. Use
2
for the second digit,
3
for the third
digit, and
4
for the fourth digit.
Importants:
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset
procedure is not successful.
PROGRAMMING WITH THE 4-DIGIT CODE
1.
1.
2.
1.
Press and hold down the
SOURCE
button for the
appliance which should be controlled and press
SET
button until the SEND indicator blinks twice.
Then back light fl ushes.
2.
Press the 4-digit code by
numeric
buttons for
appliance (code table at the end of this book)
When the procedure is successful, the SEND
indicator will blink twice.
Note:
If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.
SCANNING THE CODE TABLE
3.
5.
2.
3.
2.
1.
Switch on the appliance which should be
controlled.
BASIC OPERATION (REMOTE CONTROLLER)
NORMAL MODE
(When operating Marantz AV equipment products)
This remote controller is preset with a total of 12 types
of remote codes, including Marantz TV (television),
DVD, VCR (VCR deck), DSS (satellite broadcasting
tuner), TUNER, CD, CD-R, DMP, TAPE (tape deck),
AUX1, AUX2, and AMP (amplifi er).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
1.
Press
the
SOURCE
button.
For this example, press DVD.
Pressing the
SOURCE
button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifi er on other source, press
the
SOURCE
button twice (double-click). The
code is sent, and then the amplifi er source
changes to DVD.
SETTING THE BACK LIGHT
Pressing the Light button located on the side of
the remote controller lights the remote controller’s
backlight. Pressing the button again while the backlight
is lit lights the backlight for another 2 seconds.
To turn off back light, press and hold down the
SET
and
OFF
button until SEND indicator blinks twice.
To turn on it again, press and hold down the
SET
and
ON
button until SEND indicator blinks twice.
Initial is back light ON.
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote controller is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, CD, DVD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
controller.
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
Remote controller
source name
Corresponding preset
code
Device name
TV
TV
Television
DVD
DVD
DVD player
CD
CD
CD player
DSS
SATELLITE
Satellite broadcasting
tuner equipment
SR4003̲U̲01̲E2̲2.indd 34
SR4003̲U̲01̲E2̲2.indd 34
08.6.20 5:06:32 PM
08.6.20 5:06:32 PM
