37
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTIONS
TROUBLESHOOTING
HDMI
SYMPTOM
CAUSE
REMEDY
The display does not appear
over an HDMI connection.
The connected monitor or projector does not support HDCP.
• Connect to equipment that supports HDCP.
• Please change the method of connection.
The HDMI input of on the TV is not on.
Set HDMI input so that it turns on, as explained in the TV’s instruction manual.
The HDMI output on the source component (DVD, Set Top Box,
etc.) is not on.
Set HDMI output so that it turns on, as explained in the source component’s instruction manual.
The HDMI mode is not correctly set on the unit.
Set HDMI input on the FUNC INPUT SETUP menu as explained on page 15.
The HDMI output video resolution of the source component (DVD,
Set Top Box, etc.) does not match the TV specifi cations.
Set the resolution so that it matches, as explained in the instruction manuals of both components.
The device is connected with a non-standard HDMI cable.
The 5 m or shorter cable is recommended to ensure stable operation and prevent image quality
deterioration.
Power to the unit is off. (When the unit is on standby, HDMI
connections cannot be turned on.)
Turn on the power to the unit.
The connection between HDMI components was not
authenticated.
Shut off and then turn the power back on to the unit, TV and source component.
The OSD menu does not appear
over an HDMI connection.
The unit SETUP menu does not support HDMI output.
Use the COMPONENT VIDEO, S-VIDEO or VIDEO output.
Time is needed for the display of
an HDMI connection to appear.
The connection is being authenticated between the HDMI
devices.
There is nothing wrong with the system. Some HDMI devices require time for authentication.
Audio is not played back over an
HDMI connection.
The HDMI audio output of the source component (DVD, Set Top
Box, etc.) is not on.
Set the HDMI audio output so that it turns on, as explained in the source component’s instruction
manual.
The signal format of the source component (DVD, Set Top Box,
etc.) is not supported by the unit.
Set the HDMI audio output so that it can connect to the unit, as explained in the source component’s
instruction manual.
The unit is set to the HDMI audio “THROUGH” mode.
In the “THROUGH” mode, sound is not produced from the unit. Set it to “ENABLE”. (see page 24)
DVD-Audio is not played back
over an HDMI connection.
The DVD player does not support CPPM, therefore it cannot
output HDMI audio.
• Use a DVD-Audio player that supports CPPM.
• Turn on PCM downsampling on the DVD player.
• Use an analog connection.
Super Audio CD is not played
back over an HDMI connection.
The current HDMI connection does not support Super Audio
CDs.
Use an analog connection.
DISP
MULTI
AUTO
TUNED
ST
V – OFF
NIGHT
PEAK
ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT
DISC 6.1
MT X 6.1
SPKR
B
EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SL
S
SR
LFE
SURROUND MODE
PURE DIRECT EXIT
CLEAR
FRONT KEY (BUTTON) LOCK OF THE UNIT
If the
PURE DIRECT
and
EXT
buttons on the front
panel are both pressed at the same time for three
seconds or more, all the buttons on the front panel,
(excluding the
POWER ON/OFF
button), as well as
the
INPUT SELECTOR
knob and
VOLUME
knob,
will become locked. “F-KEY LOCK!” will appear in
the display.
Release the lock by pressing the same two keys
again at the same time for three seconds or more.
“F-KEY UNLOCK” will appear in the display, and the
keys will unlock.
GENERAL MALFUNCTION
If the equipment malfunctions, this may be because
an electrostatic discharge or AC line interference has
corrupted the information in the equipment memory
circuits. Therefore:
- disconnect the plug from the AC line supply
- after waiting at least three minutes, reconnect
the plug to the AC line supply
- re-attempt to operate the equipment
Memory backup
• In case a power outage occurs or the power
cord is accidentally unplugged, this unit is
equipped with a backup function to prevent
memory data such as the preset memory
from being erased.
HOW TO RESET THE UNIT
Should the operation or display seem to be abnormal,
reset the unit with the following procedure.
To turn on the unit, press and hold the
SURROUND
MODE
and
CLEAR
buttons simultaneously for 3
seconds or more.
Remember that the procedure will reset the settings
of the SOURCE, Surround mode, delay time, TUNER
PRESET etc., to their initial settings.
Note:
Sometimes, when “PROTECT” is shown on the unit’s display, the standby indicator fl ashes slowly (twice a second).
When this happens, turn off the unit’s power and remove the power cable. Then follow the procedure described below:
• Check to ensure that the speaker cables connected to the unit have not been connected with + and - connections reversed.
• Check to ensure that the speaker cables connected to the unit are not short-circuiting (check the connections both on the unit and on the speakers).
(Check that the playback volume is not greater than the unit can handle.)
• Check that the playback volume is not greater than the unit can handle.
After completing the above checks, connect the power cable and switch the unit back ON using the remote control.
Then, after reducing the volume, start playback and check that “PROTECT” is not appearing on the display and that there is no problem with speaker connections to the unit or
with sound reproduction.
If the same problem re-occurs, please contact your local service center to have it repaired.
On rare occasions, the unit will go into standby mode with the standby indicator fl ashing rapidly (eight times a second).
When this happens, it means that some major problem has occurred with the unit.
Quickly disconnect the power cable and take the unit to your local service center to have it repaired.
SR4003̲U̲01̲E2̲2.indd 37
SR4003̲U̲01̲E2̲2.indd 37
08.6.20 5:06:34 PM
08.6.20 5:06:34 PM
