28
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTIONS
ADV
ANCED
OPERA
TION
ATTENUATION TO ANALOG INPUT SIGNAL
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“
PEAK
” indicator will light up on the front display. If
this happens, you should press the
ATT
button on
the remote controller.
“
ATT
” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD/CDR-OUT and VCR-OUT.
This function is memorized for each individual input
source.
7.1 CH INPUT
This unit is equipped for future expansion through the
use of Multi channel Super Audio CD multichannel
player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the
Monitor Outputs
.
This permits simultaneous viewing with video
sources.
2.
4.
1.
DISP
MULTI
AUTO
TUNED
ST
V – OFF
NIGHT
PEAK
ANALOG
DIGITAL
ATT
SLEEP
SURR
AUTO
DIRECT
DISC 6.1
MT X 6.1
SPKR
B
EQ
DIGITAL
SURROUND
AAC
PCM
L
C
R
SL
S
SR
LFE
1.
4.
3.
1.
Select a desired Video source to decide the
routed video signal to the
Monitor Outputs
.
2.
Press
the
7.1
button on the remote controller to
switch the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the
CH.SEL
button on the
remote controller.
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –10 to +10 dB.
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
4.
Adjust the main volume with the
MAIN VOLUME
knob or the
VOLUME
buttons on the remote
controller.
To cancel the 7.1 CH. INPUT setting, press
7.1
on the
remote controller.
Notes:
• 7.1 CH. Input mode bypasses the internal surround
processing, so SURROUND mode cannot be
selected.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
DISP
MULTI
AUTO
SLEEP
SURR
AUTO
HT-EQ (HOME THEATER EQUALIZER)
1.
2.
At cinemas, the front left, front right and center
speakers are located behind the screen. So, screen
damping is taken into account when mastering movie
software, with an emphasis on high frequencies.
When playing back such software at home, the
signal takes on different characteristics from those
at the cinema. This unit includes HT-EQ to rectify
the sound difference between that experienced at a
cinema and in a home theater, allowing you to enjoy
the same sound you would experience at the cinema
at home. The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• SOURCE
DIRECT
• When VIRTUAL is set for the surround mode
1.
Press
the
HT EQ
button on the remote
controller.
“EQ” indicator on the front panel will illuminate,
indicating the HOME THEATER EQUALIZER
has been activated.
2.
To cancel this function, press the
HT EQ
button
again.
“EQ” indicator on the front panel will be
turned off, indicating the HOME THEATER
EQUALIZER has been deactivated.
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the unit.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED. (Refer
page 22 : System Setup)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
unit.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, this unit turns ON
and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2.
The power to the unit switches to STANDBY
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if this unit is set to
a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
SR4003̲U̲01̲E2̲2.indd 28
SR4003̲U̲01̲E2̲2.indd 28
08.6.20 5:06:29 PM
08.6.20 5:06:29 PM
