19
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTIONS
ADV
ANCED
CONNECTIONS
CONNECTING THE REMOTE CONTROL JACKS
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
signal only to the unit. Also, if a Marantz power
amplifi er (some models excluded) is connected to
one of these terminals, the power amplifi er’s, power
switch is synchronized with this unit’s power switch.
Set the REMOTE CONTROL SWITCH on the back of
other units (not the SR4003) to “EXT”.(EXTERNAL)
to use this feature.
R
R
SPEAKER SYSTEMS : 6-8 OHMS
SPEAKER SYSTEMS : 6-8 OHMS
R
R
L
L
L
L
L
L
R
R
IN
IN
OPT
OPT
DIGITAL OUT
DIGITAL OUT
C
CR
R
//
P
PR
R
C
CB
B
//
P
PB
B
Y
Y
DIGITAL IN
DIGITAL IN
OUT
OUT
IN
IN
CD/CDR
CD/CDR
OUT
OUT
IN
IN
TAPE
TAPE
VCR
VCR
DVD
DVD
AUDIO
AUDIO
DSS
DSS
IN
IN
OUT
OUT
C
CR
R
//
P
PR
R
C
CB
B
//
P
PB
B
Y
Y
DSS
DSS
DVD
DVD
VCR IN
VCR IN
VCR OUT
VCR OUT
MONITOR OUT
MONITOR OUT
INPUT
INPUT
1
1
INPUT
INPUT
2
2
CENTER
CENTER
FRONT
FRONT
SURROUND BACK
SURROUND BACK
S. SPEAKER B
S. SPEAKER B
SURROUND
SURROUND
AC IN
AC IN
MONITOR
MONITOR
OUT
OUT
INPUT
INPUT
3
3
COMPONENT
COMPONENT
VIDEO
VIDEO
OUT
OUT
REMOTE CONT.
REMOTE CONT.
2
2
1
1
4
4
3
3
AC OUTLETS
AC OUTLETS
120V 60Hz
120V 60Hz
SWITCHED
SWITCHED
1.25A 150W
1.25A 150W
MODEL N
MODEL NO. SR4003
INPUT 1
INPUT 1
IN
IN
FLASHER
FLASHER
IN
IN
OUT
OUT
REMOTE CONT.
REMOTE CONT.
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
DVD player
CD recorder
CD player
OPTION
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the unit, be sure
to always disable operation of the infrared sensor on
the unit by using the following procedure.
1.
Hold down the
SURROUND MODE
button and
MENU
button on the front panel at the same
time for fi ve seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press
the
1
or
2
cursor button to change this to
“IR=DISABLE”.
4.
Press
the
ENTER
button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note:
Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the unit will be unable to receive remote
control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
SR4003̲U̲01̲E2̲2.indd 19
SR4003̲U̲01̲E2̲2.indd 19
08.6.20 5:06:26 PM
08.6.20 5:06:26 PM
