background image

             AVS A-SERIES INSTALLATION MANUAL - GEN 2 VER 5 

 

16 

 

Changing programmable features 

 

 

The AVS A-Series programming mode is very quick and easy to use. Follow the steps below to change any of 
the programmable features: 

 

1.

 

Find the Register (1 or 2) in which the feature is located. 

 

2.

 

Set the vehicle up as described to access the required Register. e.g. to access Register 1 close all doors, 
bonnet and boot, arm and disarm alarm then turn ignition on, off and back on. 

 

3.

 

Press  the 

  button  on  the  remote  the  number  of  times  for  the  function  you  wish  to  change.  

e.g. for  arm  and  disarm  chirps press  the 

  button  two  times.  Each  press  of  the  button  will be 

confirmed by a flash of the indicators and dash LED and a chirp from the siren if connected. 

 

4.

 

Turn the ignition off. 

 

5.

 

The system will then confirm whether the feature is on or off. If the feature is enabled (turned on) the 
siren will chirp once. If the feature is disabled (turned off) the siren will chirp twice. 

 

Programming features Register 1 

 

Vehicle set up:        Close all doors, bonnet & boot, arm & disarm alarm then turn ignition 

on, off & on.

 

 

Feature: 

Arm and disarm chirp 

Press the 

 button 

this many times:

 

Factory setting: 

ON 

Description: 

One chirp on arm and two chirps on disarm. 

Feature: 

No door ajar warning 

Use if the car has factory interior light delay 

Press the 

 button 

this many times:

 

Factory setting: 

OFF 

Description: 

When  this  feature  is  ON,  the  door  ajar  warning  feature  is  removed  so  the 
indicators and siren will not chirp for three seconds if the door is left open. It will 
ignore the door, bonnet/boot & aux circuits for 45 seconds upon arming. 

Feature: 

Instant boot release/On board turbo timer shut down 

Press the 

 button 

this many times:

 

Factory setting: 

OFF 

Description: 

When this feature is ON, the boot release button will only require pressing once 
rather than holding down for three seconds to open an electric boot or shut down 
the On-board turbo timer before the preset time. 

Feature: 

Negative on alarm/pager out 

Press the 

 button 

this many times:

 

Factory setting: 

OFF 

Summary of Contents for AVS 4406037



































Reviews: