background image

 

1.GENERAL WARNING BEFORE OPERATING THE UNIT

 

 

 

Please check the conformity of waste gas , water and electric infrastucture  of  the area   

 

to the necessary technical parameters where the boiler will be installed. 

 

 

For safe use of electricity , make sure that the grounding of the installation is isolated 
and there is no phase. 

 

 

Your boiler is under guarantee for 2 years against component and production defects as  
long as  it is used in line with the suggestions in this manual. Our company cannot be held 
liable for any misuse of the product. 

 

 

Please do not use the boiler out of its purpose. The boiler is designed to supply hot water 
(maximum 90 degrees) to your heating system. 

 

 

Clean air must always be provided in the area where the boiler is installed. Due to reasons of 
security,  the installation of the boiler to closed areas with human presence is strictly 
forbidden. 

 

 

Please do not operate the boiler without water. Do not feed cold water to hot boiler. If,for 
any reason the boiler temprature is over 90 degrees, do not attempt to feed cold water to the 
boiler until the boiler temprature drops down to 40 degrees. The best solution for over 
heated boiler is to take out burning coal outside of the boiler 

 

 

Please do not drain the system water except repairing or during times of frost. 
Antifreeze   material can be added to sytem water up to 15% 

 

 

During operation, the temprature difference between return and flow can be maximum 20 

 

degrees. 

 

 

Water with high calcer rate is extremely dangerous for boiler and installation. In this 
case, please use water softeners . Product failures as a result of blocked water passes is 
out of scope of factory guarantee 

 

 

Each year,before start of heating season,the boiler’s chimney connection and internal parts 

 

must be checked and cleansed. This will enable efficient operation of the boiler. 

 

 

Please do not take hot water out of the boiler for domestic use purposes 

 

 
 
 
 
 
 
 
 
                                                                               

      

 

 
 
 
 

Summary of Contents for 25 MKK-S





















Reviews: