23 ENGLISH
NOTICE:
"J ^
the factory. Do not remove the lower fences.
NOTICE:
If the upper fence is still loose after tight-
J J
" J
You don't need to use it unless needed.
You can store the upper fences onto the holder when
not in use. Use the clip on the upper fence to hold it on
the holder.
j
Fig.39:
1.
Holder
2.
Upper fence
3.
Clip
Vertical vise
WARNING:
The workpiece must be secured
(j%:#^#'.y]]
)]<(.;#y)#.^<')[).\)|']
the vise during all operations.
If the workpiece is
not properly secured against the fence the material
may move during the cutting operation causing
possible damage to the blade, causing the material
to be thrown and loss of control resulting in serious
j
Fig.40:
1.
Vise arm
2.
Vise rod
3.
Clamping screw
4.
Vise knob
The vertical vise can be installed in two positions on
either the left or right side of the base. Insert the vise
rod into the hole in the base.
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the screw. If the clamping screw contacts
the carriage, install it on the opposite side of vise arm.
Make sure that no part of the tool contacts the vise
when lowering the handle all the way. If some part
contacts the vise, re-position the vise.
! J A@
turn base. Position the workpiece at the desired cutting
A
NOTE:
For a quick setting of workpiece, turning the
vise knob to 90° counterclockwise allows the vise
knob to be moved up and down. To secure the work-
piece after setting, turn the vise knob clockwise.
Horizontal vise
Optional accessory
WARNING:
%|#:y(Y]#])] )'y).<]\%Y\$-
|'y)<.]'%] )|Y($X')\)'yX(YX)(%:y)\<()
If
the workpiece is not properly secured the material
may move during the cutting operation causing
possible damage to the blade, causing the material
to be thrown and loss of control resulting in serious
WARNING:
).\<]]'.^#] '.|Y($X')\)
y<\
#y;#y);Y#(y#^#'.y]]
)[).\)#%|#:y
use the horizontal vise.
CAUTION:
When cutting the workpiece of the
]
'\$.)yy¢jjY(]
'..)(j#$)y<()]Y<y)#
spacer block to secure the workpiece.
The horizontal vise can be installed in two positions on
either the left or right side of the base. When performing
22.5° or greater miter cuts, install the horizontal vise on
the side opposite the direction in which the turn base is
to be turned.
j
Fig.41:
1.
Vise plate
2.
Vise nut
3.
Vise knob
<@ AJ
released, and rapidly moves in and out. To grip the
workpiece, push the vise knob forward until the vise
J A@A-
wise. Then turn the vise knob clockwise to secure the
workpiece.
NOTE:
The maximum width of workpiece which can
be secured by the horizontal vise is 228 mm.
Holders
WARNING:
%|#:yy<XXY(]#%Y.^|Y($X')\)
so it is level with the top surface of the turn base
for an accurate cut and to prevent dangerous loss
of tool control.
Proper workpiece support will help
avoid blade pinch and possible kickback which may
To hold long workpieces horizontally, holders are pro-
vided on both sides of the tool. Loosen the screws and
extend the holders to the appropriate length for holding
the workpiece. Then tighten the screws.
j
Fig.42:
1.
Holder
2.
Screw
OPERATION
WARNING:
Make sure the blade is not con-
]#\]'.^]
)|Y($X')\))]\;)[Y()]
)y|']\
is turned on.
Turning the tool on with the blade in
contact with the workpiece may result in kickback and
WARNING:
[])(#\<]]'.^YX)(#]'Y.Y.Y]
raise the blade until it has come to a complete
stop.
The raising of a coasting blade may result in
J A
WARNING:
~Y.Y]X)([Y(j#.:#<y]j).]
y<\
#y]<(.'.^^('X$.Y;#.%))(yY.]
)]YY%
while the blade is rotating.
#J
Summary of Contents for LS1219
