background image

20

ENGLISH

2.

 

Lift the lock tab slightly outwards and open the 

filter cover of the dust case.

1

2

Fig.44

►    

1.

 Filter cover 

2.

 Lock tab

3.

  Remove the filter from the filter case.

1

2

Fig.45

►    

1.

 Filter 

2.

 Filter case

4.

  Attach a new filter to the filter case, and then 

attach the filter cover.

5.

 

Close the cover of the dust case, and then attach 

the dust case to the dust collection system.

Replacing sealing cap

A damaged or worn-out sealing cap may affect the dust 

collecting performance. Replace the sealing cap with 

new one as appropriate, aligning its guide projection 

with guide notch on the nozzle head.

1

2

3

4

Fig.46

►    

1.

 Sealing cap 

2.

 Guide projection 

3.

 Nozzle head 

4.

 Guide notch

Storage

NOTICE:

 

When not in use for a certain period of 

time, the nozzle guide needs to be extended to 
approximately 100 mm from its fully shortened 
position.

 Failing to do so may damage the duct hose 

pre-installed in the nozzle guide.

1

2

Fig.47

►    

1.

 Guide adjustment button 

2.

 Approx. 100 mm

OPERATION

CAUTION:

 

Always use the side grip (auxiliary 

handle) and firmly hold the tool by both side grip 

and switch handle during operations.

CAUTION:

 

Always make sure that the work-

piece is secured before operation.

CAUTION:

 

Do not pull the tool out forcibly 

even the bit gets stuck. Loss of control may 
cause injury.

NOTICE:

 

Before using the dust collection sys-

tem with the tool, read the section about the dust 
collection system.

NOTE:

 If the battery cartridge is in low temperature, 

the tool’s capability may not be fully obtained. In this 
case, warm up the battery cartridge by using the 
tool with no load for a while to fully obtain the tool’s 
capability.

Fig.48

Summary of Contents for HR009GZ01

































Reviews: