12 ENGLISH
Changing assist type
This tool employs assist function that offers several easy-to-use application modes for driving screws with good
control.
The type of the application mode changes every time you press the button
.
You can change the assist type within approximately one minute after releasing the switch trigger.
NOTE:
You can extend the time to change the assist type approximately one minute if you press the button ,
,
or the quick mode-switching button.
►
Fig.10
Application mode
(Assist type displayed
on panel)
Maximum blows
Feature
Purpose
Wood mode *
4,400 min
-1
(/min)
This mode helps to prevent a screw from falling at
the beginning of driving. The tool drives a screw
with low-speed rotation at first. After the tool starts
to impact, the rotation speed increases and reaches
the maximum speed.
Tightening long screws.
T mode (1) *
–
(The tool stops rotating
soon after impact starts.)
This mode helps to prevent the screws from
over-tightening. It also accomplishes quick oper-
ation and good finish at the same time. The tool
drives a screw with high-speed rotation and stops
soon after the tool starts to impact.
NOTE:
The timing to stop the driving varies depending
on the type of the screw and material to be
driven. Make a test driving before using this
mode.
Driving self-drilling
screws to a thin metal
plate with good finish.
T mode (2) *
2,600 min
-1
(/min)
This mode helps to prevent the screws from
breakage and stripping. It also accomplishes quick
operation and good finish at the same time. The tool
drives a screw with high-speed rotation and slows
down the rotation when the tool starts to impact.
NOTE:
Release the switch trigger as soon as the tight-
ening finished to avoid overtightening.
Driving self-drilling
screws to a thick metal
plate with good finish.
Bolt mode
–
Clockwise
This mode helps to repeat screwdriving continu-
ously with equal torque. The stroke of the switch
trigger to reach maximum speed will become short
in this mode.
Counterclockwise
This mode helps to prevent a bolt from falling off.
When loosening a bolt with the tool driving in coun-
terclockwise rotation, the tool automatically stops or
slows down after the bolt/nut gets enough loosened.
The stroke of the switch trigger to reach maximum
speed will become short in this mode.
NOTE:
The timing to stop the driving varies depending
on the type of the screw and material to be
driven. Make a test driving before using this
mode.
Clockwise
Preventing over tighten-
ing of bolts.
Counterclockwise
Loosening bolts.
Bolt mode (1)
–
Clockwise
The tool stops automatically as soon as it has
started impact blows.
Counterclockwise
The impact force is 2. The tool stops automatically
as soon as it has stopped impacting.
–
Bolt mode (2)
–
Clockwise
The tool stops automatically approximately 0.3 sec-
ond later from the moment that the tool has started
impact blows.
Counterclockwise
The impact force is 4. The tool stops automatically
as soon as it has stopped impacting.
–
Summary of Contents for HP001G
