Makita HP001G, Instruction Manual

Page: 9 / 96

9 ENGLISH
Torque level 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Machine screw –
Wood
screw
S oft
w ood
(e.g.
pine)
– ø 9 x 7 5 – ø 1 0 x 9 0 –
H ard
w ood
(e.g.
lauan)
– ø 9 x 7 5 – ø 1 0 x 9 0 –
High speed
Torque level 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Machine screw M4 M5 M6 –
Wood
screw
S oft
w ood
(e.g.
pine)
ø 3 .5
x 2 2
ø 4 .1 x 3 8 – ø 5 .1 x 5 0 – ø 6 .2 x 6 3 –
H ard
w ood
(e.g.
lauan)
– ø 3 .5
x 2 2
ø 4 .1 x 3 8 – ø 5 .1 x 5 0 – ø 6 .2 x 6 3 –
Electronic function
T he tool is eq uipped w ith the electronic functions for
easy operation.
•
Activ e Feedb ack sensing T echnology
If the tool is sw ung at the predetermined accelera-
tion during operation, the motor is forcib ly stopped
to reduce the b urden on the w rist.
NOTICE:
Hold the tool firmly while operating.
NOTICE:
If any malfunction occurred w ith the
electronic function, the light b links for 3 seconds,
and then, turns off. In that case, contact w ith Makita
Authorized or Factory S erv ice C enters to repair.
NOTE: T his function does not w ork if the acceleration
does not reach the predetermined one w hen the tool
is sw ung.
NOTE: If the tool is forcib ly stopped, release the
sw itch trigger, and then pull the sw itch trigger to
restart the tool.
ASSEMBLY
CAUTION:
Alw ays be sure that the tool is
sw itched off and the battery cartridge is removed
before carrying out any w ork on the tool.
Installing or removing driver bit/
drill bit
Optional accessory
Fig.9 : 1. S leev e 2. C lose 3. Open
T urn the sleev e counterclockw ise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it w ill go. T urn the sleev e clockw ise to tighten the
chuck. T o remov e the driv er b it/ drill b it, turn the sleev e
counterclockw ise.
Installing side grip ( auxiliary handle)
Fig.10: 1. S ide grip 2. Protrusion 3. Groov e 4. Arm
Alw ay s use the side grip to ensure operating safety .
Install the side grip so that the protrusions on the arm fit
in the groov es on the tool b arrel. T urn the grip clockw ise
to secure it. The grip can be fixed at desired angle.
Adjustable depth rod
Fig.11: 1. Depth rod 2. C lamp screw
The adjustable depth rod is used to drill holes of uniform
depth. Loosen the clamp screw , set to desired position,
then tighten the clamp screw .
Installing hook
CAUTION:
W hen installing the hook, alw ays
secure it with the screw firmly. If not, the hook
may come off from the tool and result in the personal
injury.
Fig.12: 1.
Groov e
2.
H ook
3.
S crew
T he hook is conv enient for temporarily hanging the tool.
T his can b e installed on either side of the tool. T o install
the hook, insert it into a groov e in the tool housing on
either side and then secure it w ith a screw . T o remov e,
loosen the screw and then take it out.
Installing driver bit holder
Optional accessory
Fig.13: 1. Driv er b it holder 2. Driv er b it
Fit the driv er b it holder into the protrusion at the tool foot
on either right or left side and secure it w ith a screw .
When not using the driv er b it, keep it in the driv er b it
holders. Driv er b its 4 5 mm- long (1 - 3 / 4 " ) can b e kept
there.