background image

[4] ADJUSTMENT

[4]-2. Adjusting Accuracy of Parallel of Base to Saw blade

Mounting Saw blade to the machine, set the machine to the lowest possible position to obtain the max. cut depth.

But, do not attach Battery to the machine.

Adjust accuracy of 90 degree cut as drawn in 

Fig. 18

.

Following two kinds of adjustment screws are used in this product. 

  1. M6x8 Hex socket head set screw for adjusting Accuracy of  90 degrees .

  2. M5x8 hex socket head set screw for adjusting Accuracy of Parallel of Base to saw blade

See the following drawing in 

Fig. 17

.  

Mounting Saw blade to the machine, set the machine to the lowest possible position to obtain the max. cut depth.

But, do not attach Battery to the machine.

Adjust accuracy of parallel of Base to saw blade as drawn in 

Fig. 19

.

Fig. 18

Fig. 18

Fig. 17

M6x8 Hex socket 

head set bolt

Apply triangular rule as per the illustration 

and adjust the accuracy of right angle by turning 

M6x8 Hex socket head set bolt with hex wrench,  

until the two sides of the adjusting jig fit to Base 

and saw blade completely. 

1. M6x8 Hex socket head set screw

    for adjusting accuracy of 90 degree

    of Base to saw blade

2. M5x8 Hex socket head set screw

    for adjusting accuracy of parallel

    of Base to saw blade

Triangular rule or 1R208

Hex wrench

[4]-1. Adjusting Accuracy of 90 degree cut

Base

Rear side 

of  Base

1. Loosen M5x8 Hex socket head set screw

    with Hex wrench a little bit.

2. Apply square to the machine as per the 

    illustration.

3. Adjust by moving the rear side of base,

    until the Square fits both to the saw blade 

    and the front edge of base.

M5x8 Hex socket 

head set screw

Square

Saw blade

Front edge of

Base

R

epair

 P 1

3

/ 1

6

Summary of Contents for BHS630

















Reviews: