3
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
Symbols
END227-1
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
...... Read instruction manual.
...... Wear safety glasses.
Intended use
ENE050-1
The tool is intended for grinding ferrous materials or
deburring castings.
Power supply
ENF001-1
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool’s plug.
General Power Tool Safety
Warnings
GEA005-3
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit.
Cluttered or dark
areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool.
Distractions can cause you
to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric
shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase
the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase
the risk of electric shock.
8.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of
electric shock.
10.
Use of power supply via a RCD with a rated
residual current of 30 mA or less is always
recommended.
Personal safety
11.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
1.
Switch trigger
2.
Lock button
3.
Inner flange
4.
Hex nut
5.
Outer flange
6.
Grinding wheel
7.
Sleeve
8.
Spindle
9.
Limit mark
10. Brush holder cap
11. Screwdriver
Model
9105
Maximum wheel capacity (dia.)
125 mm x 19 mm
No load speed (min
-1
)
4,800
Overall length
550 mm
Net weight
5.5 kg
Safety class
Class I
Summary of Contents for 9105
