Programming of the system's GSM-module
1. Call the SIM-card number the vehicle security system.
2. Enter a personal code in case of necessity.
3. Press "#", the system will go to the programming mode and offer to program phone
numbers for alerts and customer-service numbers.
4. If necessary programming of this or that number - press the proposed button. If the
selected button is already programmed for any number - the system will offer to remove it
and to program another number.
5
Enter full phone number in international format or abbreviated USSD-number of
customer service and press “grid”.
6.
When pressing “grid”, the system will speak the entered phone number and offer
to program numbers the following.
7. At the end of the programming session - break the connection, or press "asterisk"
to return to the remote control mode.
Note 1:
The phone numbers are entered in the international format without the sym-
bol «
+
»: 38067
×××××××
; 38050
×××××××
; 38063
×××××××
; etc.
Note 2:
Service number for checking balance funds in your account of the SIM-card
of the security system is determined by GSM-operator serving this SIM-card.
Note 3:
Service numbers for sending a report on the location of the vehicle are en-
tered in the event that the phone operator supports location services of your own phone and
sending locations to another phone number. These service numbers are determined by
GSM-operator.
Note 4:
If the operator of the system's SIM-card does not support the location service
of your own phone, you can use the location service of "friend." For this purpose, you must
firstly install the system's SIM-card in any additional telephone, arrange an order of service
from the phone of the vehicle owner, and allow continuous monitoring of your location
from an additional phone.
The factory setting of service numbers: «
*
111»; «
*
145
*
1
*
»; «
*
145
*
1
*
1
*
».
Adjustment of sensors sensitivity
The system is equipped with a three-zone impact, tilt and displacement sensors.
The system can also be equipped with a three-zone motion sensor.
The first zones of sensors are designed to provide warnings of surrounding by sup-
plying short sound signals.
The second zones of sensors are designed to recording all kinds of effects on the ve-
hicle, turning on the alarm and sending the alarm GSM-messages.
The third zones of sensors are designed to provide full protection of the vehicle in the
"Security with the engine running" mode. There is an instantaneous switching off of the en-
gine and transition of the system into the standard armed mode with the activation of the
alarm and sending the alarm GSM-messages at activation of the third zones.
M880
OPERATION MANUAL
21
Sensitivity adjustment via a remote key fob:
1. Initial state - the armed mode is enabled.
2. To enter the adjustment mode, press and hold a certain pair of the remote key fob
buttons to the first, second or third flash of the remote key fob's LED - the system will give
1, 2 or 3 sound signals and goes into adjustment mode of the first, second or third zone of
selected sensor:
and
–
impact sensor
and
–
tilt sensor
and
–
displacement sensor
and
–
motion sensor
3. Press the remote key fob button
to increase or button
– to decrease the sensi-
tivity of the regulated zone - sensitivity change is confirmed by supply of short sound sig-
nals.
4. Test the sensitivity of the sensor by corresponding action. Apply few control im-
pacts to the vehicle body (for adjustment impact sensor), make few jacking (for adjustment
of tilt sensor) or movements of the vehicle (for adjustment of displacement sensor) or make
few movements in the interior or in the vicinity of the vehicle (for adjustment of motion
sensor) - the system will give short sound signals at activation of the regulated zone.
If
necessary, repeat the adjustment (point 3)
5. Press the remote key fob button
– the system will give 3 sound signals, remem-
bers new sensitivity level of the regulated zone and exits from the adjustment mode.
Note 1:
If during adjustment of the sensor, the sensitivity of its zones will reach limit
levels - the system will give long sound signals.
Note 2:
If during adjustment of the sensors within three minutes will not press any
button - the system will automatically exit from the adjustment mode.
Sensitivity adjustment via a smartphone:
Adjustment of sensor sensitivity by a smartphone (by GPRS-channel) allows independent
adjustment of the sensitivity of each of the three zones of impact, tilt, displacement and motion
sensors.
Control of the security system via a smartphone also provides the possibility of rapid
differential switching off and on of any zones of sensors with preservation of their sensitiv-
ity.
Automatic adjustment of sensitivity:
Sensitivity of precisely this particular zone will be automatically decreased at activa-
tion of one or another zone of this or that sensor.
Sensitivity zones will decrease to such levels at which the false activations of sensors
are minimized. Incremental restoration of sensitivity of "understatement" zones of the sen-
sors will occur at reduction of the noise level. So, if for some zones within 15 minutes will
not be recorded activations at higher sensitivity levels, the system will automatically come
back to these levels.
Restoring the level of sensitivity of sensor's zones will occur up to the levels set
while adjusting via remote key fob or smartphone.
OPERATION MANUAL
M880
22
