Magnum M880 Operation Manual Download Page 5

Page: 5 / 13

Disarming via a remote key fob

1. If necessary single disable or enable of audio confirmation – press button

the remote key fob.

2. Press button

of the remote key fob – the system will give 2 sound and 2 light

signals or only 2 light signals, unlocks the central door locking, send the owner of the vehi-
cle GSM-notification about disarming and activates the timer of automatic recovery of
arming - system's LED will blink with a frequency of 4 flashes per second.

3. To cancel the automatic recovery of arming, open the door, trunk, switch on the

ignition, or briefly press one of the buttons

of the remote key fob – system's

LED stops flashing.

Note 1:

If recovery of arming will not be canceled after 30 seconds, the system au-

tomatically returns to the armed mode. The recovery time of arming and the recovery func-
tion are programmable.

Note 2:

At each disarming, the system produces a short call to the owner, without the

need accepting the call by them. Duration of the short call and the function are program-
mable. Factory setting is 2 seconds.

Note 3:

SMS-messages about disarming, as well as voice messages with the manda-

tory confirmation of message reception by the owner of the vehicle can be programmed in
case of necessity.

Note 4:

Voice and SMS-messages can be sent as at each fact of disarming system,

and only in cases of prior "cocking" of the system by ghost button (any standard or addi-
tional button).

Note 5:

Opening the second stage of the central door locking is performed by press-

ing the button

of the remote key fob after disarming the system.

Note 6:

Sound and light confirmation signals are programmable independently of each

other and can be changed by the installer.

Note 7:

If alarm events were recorded during the arming

mode - the system will give

additional sound signals within 2 seconds after disarming:

1 long signal

– hood was opened;

2 long signals

– door was opened;

3 long signals

– trunk was opened;

4 long signals

– ignition was switched on;

5 long signals

– battery was disconnected;

1 short signal

– impact sensor was tripped;

2 short signals

– tilt sensor was tripped;

3 short signals

– displacement sensor was tripped;

4 short signals

– motion sensor was tripped;

5 short signals

– additional sensor was tripped;

6 short signals

– connection problems with the GSM operator.

Note 8:

To reset the events memory is necessary to disarm the system, open the

door, turn on and turn off the ignition.

M880

OPERATION MANUAL

Disarming via a phone

In case the remote key fobs are missing, defective or for whatever reason, cannot be

used - the system can be disarmed by the mobile phone:

1. Call the SIM-card number of the vehicle security system.
2. Enter a personal code, in case of necessity.
3. Press the "asterisk" to switch to the remote control mode.
4. Press button "2" of a phone - the system disarms.
5. Press again button "2" to open the central locking system.
6. Break the connection (see "System control via a phone").

Note 1:

When controlling the security system via a mobile phone - listen to the voice

prompts.

Note 2:

When disarming the system via a phone, confirming sound and light signals

are not given.

Note 3:

When disarming the system via a phone, the function of automatic recovery

of arming is not activated.

Emergency disarming the system

In case the remote key fobs and mobile phone are missing, defective or for whatever

reason, cannot be used - the system can be disarmed by the procedure of emergency dis-
arming:

1. Open the door by the standard key - the alarm mode will be switched on.
2. Ignoring the alarm, enter a complete personal code - the system will give 2 sound

and 2 light signals and disarms - system's LED stops flashing (see "Entering a personal
code").

Entering a personal code

Personal code can be entered as via the ignition switch and the LED, and through the

ignition switch, LED and the remote key fob:

1. Turn on the ignition - in a second, system's LED indicator will begin digit-by-digit

counting the numbers of a personal code by short flashes.

2. After the flash, corresponding 1st digit of the code, press button

of the remote

key fob or switch off the ignition - LED will start to count the second digit.

3. After the flash, corresponding 2

digit of the code, press button

of the remote