background image

IMPORTANT SAFETY INSTRUCTIONS:

CAUTION: 

To reduce the risk of electric shock, do not remove the 

cover. There are no user-serviceable parts inside; it is 

recommended that only qualified personnel service this 

component.

OWNER’S MANUAL: 

Before powering up the equipment, read all 

safety and operating instructions and follow them as instructed. 

Retain the safety and operating instructions for future reference.

ATTACHMENTS: 

Use only those attachments recommended by 

the unit manufacturer, as others may cause hazards.

ACCESSORIES: 

Do not place the unit on an unstable cart, stand, 

tripod, bracket, or table. The unit may fall, causing injury to a 

person or damage to the unit. Mount the unit according to the 

manufacturer’s instructions with the suggested mounting 

accessory.

WATER AND MOISTURE: 

Do not use the unit near water (for 

example, near a swimming pool, bathtub, washbowl, kitchen sink, 

or laundry tub) or in a damp environment (like a basement or 

outside in the rain).

OBJECT AND LIQUID ENTRY: 

Do not push objects of any kind 

into the unit through openings as they could touch dangerous 

voltage points and short-out parts, possibly resulting in a fire or 

electric shock. Avoid spilling liquid of any kind on the unit. If water 

or any metal object (such as a paper clip, coin, or staple) 

accidentally falls inside the unit, disconnect it from the AC power 

source immediately and contact Margules Audio for further 

instructions.

HEAT: 

Position the unit away from heat sources such as 

radiators, heat registers, stoves, or other units (including 

amplifiers) that produce heat.

GROUNDING OR POLARIZATION: 

As a safety feature, the unit 

may be equipped with a polarized alternating current line plug, in 

which one blade is wider than the other. This plug will fit into the 

power outlet only one way. If you cannot insert the plug fully into 

the outlet, try reversing the plug. If the plug still does not fit, 

contact a licensed electrician to update your obsolete outlet. Do 

not break the safety purpose of the polarized plug.

POWER SOURCES: 

Operate the unit only from the power source 

indicated on the marking label. If you are unsure of the type of 

power supplied to your home, consult your unit dealer or local 

power company.

3

Summary of Contents for TT10


















Reviews: