MacDon A40-D Assembly Instructions Manual Download | Manualshive

Page: 61 / 120

background image

ASSEMBLING THE MACHINE

3.14

Routing Reverser Valve Jumper Hose

An optional valve block to reverse the header drive in the event of plugging

MAY HAVE BEEN

installed on

the M150, M155, M155

E4

, and M200 windrowers.

If reverser valve block (A) is installed, proceed as follows. Otherwise, disregard this procedure.

IMPORTANT:

A jumper hose on the reverser valve has a specific
routing for each model of header. Do

NOT

operate

the header unless hose is routed as shown.

1.

Move left-hand windrower platform to the open position
to expose hydraulic valve blocks.

2.

Check the routing of the jumper hose as follows and
change as required.

3.

Route jumper hose (B) from C2 conveyor circuit (C) to
CR on reverser block (A) as shown.

NOTE:

For draper headers, CR is routed to port R4
(as shown in image to the right) on reverser
block. Reroute jumper hose (B) when switching
between draper and auger headers. This
prevents draper header reel damage and
improper operation, which occurs if reel runs
backwards.

Figure 3.108: Hose (B) Position (A40-D on M200
Shown – M150, M155, and M155

E4

Similar)

NOTE:

Jumper hose re-routing is unnecessary if hay
conditioner is not installed on draper header.

NOTE:

The draper header reverser function is suppressed
unless hay conditioner is activated in Windrower
Setup using the cab display module (CDM).

Figure 3.109: Hose Position (Draper Header
on M150 Shown – M155, M155

E4

, and M200

Similar)

147913

55

Revision A

«
...
59
60
61
62
63
...
»

Summary of Contents for A40-D

























































































































Reviews:

No comments

Related manuals for A40-D

Brand: T-Drill Pages: 75

Brand: Zeiss Pages: 38

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

Brand: ParaBody Pages: 3

Brand: Hach Pages: 52

Brand: hager Pages: 2

Brand: ICP DAS USA Pages: 45

Brand: Velp Scientifica Pages: 12

Brand: Yamaha Pages: 24

Brand: J&M Pages: 33

Brand: Qlight Pages: 4

ST70 Instrument

Brand: Raymarine Pages: 12

Brand: Raven Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands