manualshive.com logo in svg

Maaselan Kone Oy Hakki Pilke 37 Series, Instructions For Assembly, Operation And Maintenance, Page: 51 / 57

Share
Download
Maaselan Kone Oy Hakki Pilke 37 Series Instructions For Assembly, Operation And Maintenance Download Page 51

51 

 

 

Original 

Version 1-2011 

 
 

1.

 

Shut down the splitter and 
disconnect it from its power 
sources. 

 

2.

 

Loosen the locking nut B 
and adjust the motor 
pressure with the 
adjustment screw A. (The 
pressure increases when 
turning the screw clockwise 
and vice versa.) 
 

3.

 

Note! The maximum 
pressure for the motor is 85 
bars. This limit must not be 
exceeded! 

 

 

8.0

 

Lubricating moving parts 

 
 
 

1.

 

Grease nipple for the 
blade's drive shaft 
 
 

2.

 

Grease nipple for the 

wood measuring 

mechanism 

 

3.

 

Grease nipple for the 
main shaft bearing 
(pump side) 
 

4.

 

Grease nipple for the 
output conveyor's 
turning device (only 
in machines with a 
pivoting conveyor) 
 

5.

 

Grease nipples for 
the splitting blade's 
lifting cylinders (only 
in the Easy model) 

 

 

 

 

 

 
 
 
 
 

 

Summary of Contents for Hakki Pilke 37 Series


























































Reviews:

No comments