Maaselan Kone Oy Hakki Pilke 37 Series Instructions For Assembly, Operation And Maintenance Download Page 29 | Manualshive

Page: 29 / 57

background image

29

Original

Version 1-2011

The lever handle can be changed to
suit left or right handed users, and
the handle can be lifted to the
desired height.

The  sensitivity  of  the  input
conveyor's  movement  can  be
adjusted  with  the  lever mechanism
of  the  valve  controlling  the
conveyor.

The

adjustments

for

lever

movement are located behind the
valve cover.

Locking nuts

Adjustment nuts

Belt adjustment:

Open the locking nuts and use the
adjustment nuts to adjust the belt
tension to a suitable level. Finish by
tightening the locking nuts.

If the belt veers to the side, adjust
the belt with the adjustment nut on
that side. This will guide the belt to
the middle of the frame.

«
...
27
28
29
30
31
...
»

Summary of Contents for Hakki Pilke 37 Series


























































Reviews:

No comments

Related manuals for Hakki Pilke 37 Series

Brand: Brave Pages: 48

Brand: Brave Pages: 50

Brand: Zipper Mowers Pages: 59

Brand: red roo Pages: 2

Brand: ATIKA Pages: 96

Power Split 370 H

Brand: Texas Equipment Pages: 57

Brand: SIP Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands