manualshive.com logo in svg

Maaselan Kone Oy Hakki Pilke 37 Series, Instructions For Assembly, Operation And Maintenance, Page: 43 / 57

Share
Download
Maaselan Kone Oy Hakki Pilke 37 Series Instructions For Assembly, Operation And Maintenance Download Page 43

43 

 

 

Original 

Version 1-2011 

 
 

 

Do not use the machine if the cutting blade is visible through the cutting opening and 
the blade is not completely raised inside the guard! 

 

  

 

 
 

 

6.3

 

Replacing the cutting flange 

 

Replace the blade flange as follows: 

1.

 

Remove the blade chain according to steps 1–6 of Section 6.2. 

2.

 

Remove the flange bolts A, and detach the fastening plate B on the other side of the flange. 

3.

 

Remove the flange from the groove. 

4.

 

Place  the  new  flange  against  the  gear  wheel  C,  twist  it  into  the  groove  and  loosely  attach  the 
flange bolts A and the fastening plate B. 

5.

 

Install and tighten the blade chain according to steps 8–10 of Section 6.2. 

 
 

             

        

 

Figure 36. 

 

 

 

 

Figure 37.

 

 
 
 
 
 
 
 

 If the blade is not completely 

raised, tighten the spring 
pulling the blade by turning its 
adjustment nut.  If the 
adjustment is not enough, 
replace the spring. 

 

Summary of Contents for Hakki Pilke 37 Series


























































Reviews:

No comments