KS2V2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: [email protected]
EM-3608 Rev.9 P. 7 / 9
Alarm mode for SET1 and SET2 (P-A1, P-A2)
Changing trip operation, latching hold and relay & LED be-
havior for SET1 and SET2.
[Example]
SET1: High trip, without latching hold, coil energized (1)
→
High trip, with latching hold, coil energized (3)
SET2: Low trip, with latching hold, coil energized (4)
→
Low trip, without latching hold, coil de-energized (6)
Key
Status or Operation
Display
Current display
(PTn = 2 in this example)
Display pattern 1
Upper = ST1 (setpoint)
Lower = ST2 (setpoint)
SEL
Keep pressing the key for 7 seconds.
→
Maintain while the display indicates Pat-
tern 2, Pattern 3, and Parameter block 1,
until HYS1 is on the display.
Upper = blank
Lower = HYS1
DOWN Press the key five times.
→
Next parameter name is displayed.
Upper = blank
Lower = P-A1
SEL
Press the key once.
→
P-A1 is replaced with current setting.
Upper = blank
Lower = 1
UP
DOWN
Press the keys until the display indicates 3.
(New value is registered if the unit is not
accessed for 3 sec.)
Upper = blank
Lower = 3
SEL
Press the key once.
→
The lower display indicates the param-
eter name (P-A1) again.
Upper = blank
Lower = P-A1
DOWN Press the key once.
→
Next parameter name is displayed.
Upper = blank
Lower = P-A2
SEL
Press the key once.
→
P-A2 is replaced with current setting.
Upper = blank
Lower = 4
UP
DOWN
Press the keys until the display indicates 6.
(New value is registered if the unit is not
accessed for 3 sec.)
Upper = blank
Lower = 6
SEL
Press the key once.
→
The lower display indicates the param-
eter name (P-A2) again.
Upper = blank
Lower = P-A2
SEL
Keep pressing the key for 3 seconds.
→
Maintain while the display changes.
Display pattern 1
Upper = ST1 (setpoint)
Lower = ST2 (setpoint)
Burnout protection (bUrn)
[Example]
Changing internal input value in case of burnout
(over-range included) from downscale (L) to upscale (H).
Key
Status or Operation
Display
Current display
(PTn = 1 in this example)
Display pattern 1
Upper = ST1 (setpoint)
Lower = ST2 (setpoint)
SEL
Keep pressing the key for 7 seconds.
Upper = blank
→
Maintain while the display indicates Pat-
tern 2, Pattern 3, and Parameter block 1,
until HYS1 is on the display.
Lower = HYS1
DOWN Press the key seven times.
→
Next parameter name is displayed.
Upper = blank
Lower = bUrn
SEL
Press the key once.
→
bUrn is replaced with current setting.
Upper = blank
Lower = L
UP
DOWN
Press the keys until the display indicates H.
(New value is registered if the unit is not
accessed for 3 seconds.)
Upper = blank
Lower = H
SEL
Press the key once.
→
The lower display indicates the param-
eter name (bUrn) again.
Upper = blank
Lower = bUrn
SEL
Keep pressing the key for 3 seconds.
→
Maintain while the display changes.
Display pattern 1
Upper = ST1 (setpoint)
Lower = ST2 (setpoint)
Switching delay time for SET1 and ST2
Changing switching delay time (P-d1, P-d2) for SET1 and
SET2.
[Example]
SET1: 1 sec.
→
10 sec. SET2: 1 sec.
→
4 sec.
Key
Status or Operation
Display
Current display
(PTn = 2 in this example)
Display pattern 1
Upper = ST1 (setpoint)
Lower = ST2 (setpoint)
SEL
Keep pressing the key for 7 seconds.
→
Maintain while the display indicates Pat-
tern 2, Pattern 3, and Parameter block 1,
until HYS1 is on the display.
Upper = blank
Lower = HYS1
DOWN Press the key eight times.
→
Next parameter name is displayed.
Upper = blank
Lower = P-d1
SEL
Press the key once.
→
P-d1 is replaced with current setting.
Upper = blank
Lower = 1
UP
DOWN
Press the keys until the display indicates 10.
(New value is registered if the unit is not
accessed for 3 sec.)
Upper = blank
Lower = 10
SEL
Press the key once.
→
The lower display indicates the param-
eter name (P-d1) again.
Upper = blank
Lower = P-d1
DOWN Press the key once.
→
Next parameter name is displayed.
Upper = blank
Lower = P-d2
SEL
Press the key once.
→
P-d2 is replaced with current setting.
Upper = blank
Lower = 1
UP
DOWN
Press the keys until the display indicates 4.
(New value is registered if the unit is not
accessed for 3 sec.)
Upper = blank
Lower = 4
SEL
Press the key once.
→
The lower display indicates the param-
eter name (P-d2) again.
Upper = blank
Lower = P-d2
SEL
Keep pressing the key for 3 seconds.
→
Maintain while the display changes.
Display pattern 1
Upper = ST1 (setpoint)
Lower = ST2 (setpoint)
