M/A-Com Orion Operator'S Manual Download Page 3

Page: 3 / 80

TABLE OF CONTENTS

Page

SAFETY INFORMATION .................................................................. 5

INTRODUCTION ................................................................................ 6

USER INTERFACE ............................................................................. 7

CONTROLS .......................................................................................... 8

POWER ON-OFF VOLUME KNOB.................................................... 8

SYSTEM/GROUP CHANNEL KNOB................................................. 8

RAMP CONTROL ................................................................................ 8

SCAN ON/OFF ..................................................................................... 9

SCAN ADD/DELETE........................................................................... 9

INDICATORS ....................................................................................... 9

KEYPAD ............................................................................................. 10

DISPLAY............................................................................................. 14

RADIO STATUS ICONS.................................................................... 14

MESSAGES ........................................................................................ 15

ALERT TONES .................................................................................. 20

CALL ORIGINATE ............................................................................ 20

AUTOKEY (TRUNKED MODE ONLY)........................................... 20

CALL QUEUED (TRUNKED MODE ONLY) .................................. 20

SYSTEM BUSY (TRUNKED MODE ONLY)................................... 20

CALL DENIED (TRUNKED MODE ONLY).................................... 20

CARRIER CONTROL TIMER........................................................... 21

KEY PRESS ALERT .......................................................................... 21

DUAL CONTROL SWITCHING ....................................................... 21

OPERATION ...................................................................................... 22

TURNING ON THE RADIO .............................................................. 22

SELECTION MODE RULES ............................................................. 22

DIRECT ACCESS............................................................................... 24

MENU ................................................................................................. 24

FEATURE ENCRYPTION DISPLAY ............................................... 29

SYSTEM/GROUP/CHANNEL SELECTION .................................... 32

TRUNKED MODE OPERATION .................................................... 34

RECEIVING A CALL ........................................................................ 34

SENDING A CALL ............................................................................ 34

CONVENTIONAL FAILSOFT .......................................................... 35

EMERGENCY OPERATION ............................................................. 35

SYSTEM SCAN OPERATION .......................................................... 36

GROUP SCAN OPERATION............................................................. 38

INDIVIDUAL CALLS ........................................................................ 41

SCAT OPERATION ........................................................................... 43

TELEPHONE INTERCONNECT CALLS ......................................... 43

MOBILE DATA.................................................................................. 46

Summary of Contents for Orion

















































































Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands

M/A-Com Orion, Operator'S Manual

Search results

Summary of Contents for Orion

Reviews:

Related manuals for Orion

Brands by name

Popular brands