M/A-Com Orion Operator'S Manual Download Page 7 | Manualshive

Page: 7 / 80

background image

USER INTERFACE

The

Orion

operating controls are located on the radio's front panel (See

Figures 1 & 2). A keypad, vacuum florescent display for radio status
information, and a microphone jack are on the front panel. The front panel
also provides a rotary

SYSTEM/GROUP/CHANNEL

knob,

POWER ON-

OFF/VOLUME

control, a ramp up/ramp down control, Scan add/delete

control, and a SCAN ON-OFF control for scan operation.

The keypad is used for manual number entry for individual calls, access to a
telephone interconnect system and activation of various EDACS or
conventional features such as menu selection. Each key has an associated
LED for status indication.

The display has two lines with eight alphanumeric-characters used to show the
operational mode of the radio. There is one LED for indicating transmitter

ON

and one LED to indicate

CHANNEL BUSY

located below the

POWER ON-

OFF/VOLUME

Control

.

Figure 1 - Orion Mobile Radio SYSTEM Model Front Panel

Figure 2 - Orion Mobile Radio SCAN Model Front Panel

7

«
...
5
6
7
8
9
...
»

Summary of Contents for Orion

















































































Reviews:

No comments

Related manuals for Orion

Brand: R&S Pages: 59

Brand: Team Pages: 33

Brand: Ryobi Pages: 68

Brand: National Instruments Pages: 18

Brand: Thulos Pages: 5

Brand: Champion Pages: 28

Brand: K&S BASIC Pages: 10

Brand: Manta Pages: 6

Brand: Albrecht Pages: 16

Brand: GE Pages: 88

Brand: Feider Machines Pages: 80

Brand: Vertex Standard Pages: 41

Brand: Vertex Standard Pages: 94

Brand: Midland Pages: 26

Brand: Vertex Standard Pages: 28

Brand: Philips Pages: 2

Brand: morse Pages: 34

Brand: Hitachi Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands