background image

19

 

MESSAGE 

NAME 

DESCRIPTION 

SPKR ON

 

External Speaker On 

This is displayed when the external speaker is 
enabled. 

SPKR OFF

 

External Speaker OFF 

This is displayed when the external speaker is 
disabled. 

BANK=1-8

 

 

This is the bank of keys, which are going to 
be loaded when the key loader loads 
encryption keys. This is only valid for radios 
that support VGS, VGE, or DES encryption. 
It is displayed on line 2 of the display when 
the encryption key loader is connected. 

REGR_0x

 

Dynamic Regroup 

Indicates which group in dynamic regroup 
operation has been enabled where "x" is a 
digit of 1 to 8  (trunked mode only). 

KEY LOAD

 

 

This is displayed in line 1 of the display when 
the encryption key loader is connected. 

KEY ZERO

 

 

This is displayed on line 2 of the display 
when the operator depresses the reset and 
option buttons simultaneously for 
approximately two seconds. The encryption 
keys are zeroed. 

SYS KEY

 

System Key 

This is displayed on line 1 of the display in 
the display key mode of the menu. The key of 
the key name display is displayed in line 2. 

GRP KEY

 

Group Key 

This is displayed on line 1 of the display in 
the display key mode of the menu for trunked 
systems only. It is followed in the second line 
with a key number `KEY = <1..7>'. 

CHN KEY

 

Channel Key 

This is displayed on line 1 of the display in 
the display key mode of the menu for 
conventional systems only. It is followed in 
the second line with a key number `KEY = 
<1..7>'. 

KEY=1-7

 

 

This is displayed on line 2 of the display in 
the display key mode of the menu for 
conventional when `SYS KEY' or `CHN 
KEY' is displayed in line 1 and for trunked 
when `SYS KEY' or `GRP KEY' are 
displayed in line 1. 

PRIMARY

 

 

This is displayed on line 1 of the display 
when primary keys are enabled. 

PRS NAME

 

Personality Name 

This is displayed in line 1 of the display under 
the revision selection of menu. The 
personality name is displayed on line 2 at the 
same time. 

M/A-COM, Inc.

 

 

This is displayed on line 1 of the display 
under the revision selection of menu. The 
copyright year is shown in line 2 of display at 
the same time. 

Summary of Contents for Orion

















































































Reviews: