manualshive.com logo in svg

M/A-Com M/A-COM P7200 Series, Operator'S Manual

Share
Download
M/A-Com M/A-COM P7200 Series Operator'S Manual Download Page 23

 

23

 

Table 3: Display Descriptions 

 

Steady 

– “Busy” transmitting or receiving, Network connectivity 

Flashing

 – call queued 

 

Steady

 – Special call mode (individual or telephone)

 

 

Steady

 – Stealth mode is enabled (all tones and other displays are off, 

voice is still heard).

 

 

Steady

 – Battery charge indicator (refer to Figure 10)

 

 

Flashing

 – Low battery indicator (refer to Figure 10)

 

 

Steady

 – Transmit in encrypt mode 

Flashing

 – Receiving an encrypted call

 

 

Steady – Indicates operation in VTAC mode. 

 

Signal Strength Indicator – Indicating weaker signal (refer to 

Figure 

11

) 

 

Signal Strength Indicator – Indicating stronger signal (refer to 

Figure 11

) 

 

Figure 10: Battery Charge Indicator (Full Cycle) 

The battery charge indicators (see Figure 10) illustrate approximate level only, 
based on battery voltage. 
 

 

Figure 11: Signal Strength Indicators 

The signal strength indicators (see Figure 11) illustrate relative signal strength 
only. 

Summary of Contents for M/A-COM P7200 Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands