luxvision LRK-7000 Operation Manual Download Page 41

Page: 41 / 91

8.1.2. Automatic measurement mode

NOTE

The automatic measurement mode is composed of optimum measurement conditions and can

be measured reliably. If the patient's eyes move and it is difficult to measure, press the

measurement button on the joystick.

The mode gets converted to automatic measurement mode when MANUAL button is pressed on while in

the manual measurement mode.

While in the automatic measurement mode, measurement is carried out automatically even when the

measurement button is not pressed on when the state reaches a state in which arrangement in the device

and measurement is realized effectively.

①

(Eye height adjustment), (measurement location and focusing) process is carried out just like the

manual measurement mode.

②

Measurement

Measurement is carried out automatically when the location arrangement and focusing are

completed.

Value for new measurement result appears on the monitor screen after measurement takes place

up to the frequency (possible to select among three, five and continuous) designated on the user

Setup mode.

Up to 99 measurement frequencies are indicated and it is possible to check the measurement

values

up to the latest 10 times once again in the Display mode.

Summary of Contents for LRK-7000




























































































Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands

luxvision LRK-7000, Operation Manual

Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands