manualshive.com logo in svg

luxvision LRK-7000, Operation Manual

Share
Download
luxvision LRK-7000 Operation Manual Download Page 46

46 

 

!

 

NOTE

 

 

8.2.2. Automatic measurement mode

 

 

The automatic measurement mode is composed of optimum measurement conditions and can 

be  measured  reliably.  If  the  patient's  eyes  move  and  it  is  difficult  to  measure,  press  the 

measurement button on the joystick.

 

 

The mode gets converted to automatic measurement mode when MANUAL button is pressed on while 

in the manual measurement mode. In case of automatic measurement mode, when the state reaches a 

state in which the arrangement in the device and measurement is realized effectively, measurement takes 

place automatically even when the measurement button is not pressed on.

 

 
 
 

①

  Location arrangement and focus are adjusted just like the (measurement location and focusing) while 

in the 8.1.2 refractive power measurement mode.

 

 
 
 

②

  Measurement takes place automatically using the same method as that of the (measurement) 

process while in the 8.1.2 refractive power measurement mode.

 

 
 
 

③

 

Measurement result is printed using a method that is same as that of the (printing) process while in 

the 8.1.2 refractive power measurement mode.

 

 

8.2.2. Message List

 

 
 

"MOVE RIGHT"

 

Move stage to right.

 

"MOVE LEFT"

 

Move stage to left.

 

"CHINREST DOWN"

 

Move chinrest down.

 

"CHINREST UP"

 

Move chinrest up.

 

"DATA 

TRANSMITTING"

 

Measurement data of LRK is being transmitted to external.

 

"DATA PRINTING"

 

Measurement data of LRK is being printed.

 

"HLM DATA 

PRINTING"

 

Measurement data of LM is being printed.

 

"HDR DATA 

TRANSMITTING"

 

Measurement data of LM is being transmitted to external. 

 

"FINISH"

 

(Auto shot mode) Measurement is finished.

 

“ALIGN ERROR” 

The alignment (focus or center) is significantly failed during the 

measurement.

 

“NO SIGNAL” 

- Center or eye cannot be found.

 

- The patient’s eye blinks or moves during measurement.

 

- If this message appears while measuring model eye, the 

instrument

 

may have a problem. Contact your service engineer. 

"TRY AGAIN" 

There is too big difference from the previous measurement value. 

 

 

 

 
 

 

 

 

Summary of Contents for LRK-7000




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands