luxvision LRK-7000 Operation Manual Download Page 61

Page: 61 / 91

: Select data transmission speed with another device (9600, 57600, 115200bps)

RS232 PROTOCOL (COM1) (Off/V1/V2/Ext.)

: Setting up the transmission method (other equipment method and Version)

MODE (COM1) (Std/Avg/Misc)

: Data format setting for transmission method.

LM PRINT (Off/On):

Sets whether to print the data imported from the connected Lensmeter (US

Ophthalmic LLC LM-1) using the built-in printer of the device. When “On” is selected, the data is

printed from the device printer by pressing the print button of the lensmeter.

BPS (COM2) (9600/57600/115200)

: Select data transmission speed with other device (9600, 57600, 115200bps)

RS232 PROTOCOL (COM2) (Off/On)

: Set on if your system use second communication port.

(To use second port, RS232 Y CABLE must be connected to your device.)

MODE (COM2) (Mate/LM)

: Select the target of second communication port.

NOTE

- For the users who want LRK-7000 is connected with two devices at the same time, we

prepare the RS232 Y CABLE.

- If LRK-7000 is connected with only one device, set [RS232 PROTOCOL (COM2)] off, and

do not care about all of “COM2” options.

- LRK-7000 has only single serial port but, with the RS232 Y CABLE, you can connect two

devices to it. Followings are available connections.

Summary of Contents for LRK-7000




























































































Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands

luxvision LRK-7000, Operation Manual

Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands