luxvision LRK-7000 Operation Manual Download Page 2

Page: 2 / 91

Precautions

This product may malfunction due to the electromagnetic wave that is generated from mobile

phone, two-way radio, machinery controlled wireless and others. Do not place any device that may

affect this product nearby.

We believe that the contents of this user manual are accurate in overall since they were reviewed

carefully. However, US Ophthalmic LLC does not assume any kind of responsibility for the latent

mistake or omission that results from the use of information included in this user manual.

US Ophthalmic LLC has the right to make any kind of modification to this product or product specs

anytime without prior notice and modification may not be renewed on this document.

VER1.0

US Ophthalmic LLC

9990 NW 14

ST STE 105 Doral FL 33172

Summary of Contents for LRK-7000




























































































Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands

luxvision LRK-7000, Operation Manual

Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands