luxvision LRK-7000 Operation Manual Download Page 12

Page: 12 / 91

Where there is a hot equipment nearby.

Where the humidity is extremely high or there is a ventilation

problem.

Where the machine is exposed to excessive shocks or

vibrations.

Where the machine is exposed to chemical material or

explosive gas.

Be cautious so that things like dust and metal do not fall

inside the machine.

Don’t disassemble or open the product. US Ophthalmic LLC

does not take responsibility for the possible problems

Be careful not to block the fan of the machine.

Don’t plug the AC power cord into the outlet

unless all parts of the machine are completely

connected. Otherwise, it will cause severe

damage on the machine.

To avoid risk of electric shock, this equipment must

only be connected to a supply main with protective

earth.

Summary of Contents for LRK-7000




























































































Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands

luxvision LRK-7000, Operation Manual

Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands