luxvision LRK-7000 Operation Manual Download Page 17

Page: 17 / 91

CAUTION

For use of equipment in rated voltage less than 125Vac, minimum 6A, Type SJT or SVT,

18/3AWG, 10A, max 3.0m long: One end with Hospital Grade Type, NEMA 5-15P Other end

with appliance coupler. For use of equipment in rated voltage less than 250Vac, minimum 6A,

Type SJT or SVT, 18/3AWG, 10A, max 3.0m long: One end terminated with blade attachment

plug (HAR) Type, NEMA 6-15P.

This equipment must be installed and operated in accordance with provided instructions and

the antenna(s) used for this transmitter must be installed to provide a separation distance of

at least 20 cm from all persons and must not be co-located or operating in conjunction with

any other antenna or transmitter. End-users and installers must be provide with antenna

installation instructions and transmitter operating conditions for satisfying RF exposure

compliance.

Summary of Contents for LRK-7000




























































































Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands

luxvision LRK-7000, Operation Manual

Search results

Summary of Contents for LRK-7000

Reviews:

Related manuals for LRK-7000

Brands by name

Popular brands