Lutron Electronics seeTouch QS Application Note Download Page 3

Page: 3 / 18

Application Note #428

Lutron Technical Support Center

1.800.523.9466

Domestic:

International:

North American style wallstation

European style wallstation

Note:

Several advanced features require the use of a “raise” or “lower” button and/or a button that the

user may not be able to access on a fully assembled wallstation. In this case, the user should:

1.  Snap off the faceplate of the wallstation.
2.  remove the screws and the faceplate adapter (if present).
3.  Gently pry off the button kit

This should allow access to all buttons, status LEDs, and backlight LEDs.

Button

kit

Adapter

Faceplate

North American style wallbox

European style wallbox

Wallbox

Mounting

Screws (2)

Adapter

Screws (4)

Faceplate

Control

Adapter

Button

kit

2. remove

screws and
faceplate
adapter

(if present)

1. Snap off

faceplate

3. Gently pry

off button

kit

Wallstation Overview

Wallbox

Control

Mounting

Screws (2)

Adapter

Screws (2)

Summary of Contents for seeTouch QS



















Search results

Summary of Contents for seeTouch QS

Reviews:

Related manuals for seeTouch QS

Brands by name

Popular brands

Lutron Electronics seeTouch QS, Application Note

Search results

Summary of Contents for seeTouch QS

Reviews:

Related manuals for seeTouch QS

Brands by name

Popular brands