manualshive.com logo in svg

Lumel N32O, User Manual, Page: 21 / 69

Share
Download
Lumel N32O User Manual Download Page 21

N32O 

User's manual

21

Table 5

, 

, 

, 

Parameter 

symbol

Description

Range of changes

Input value controlling the alarm.

Default: IND 1

IND 1

 – measuring value on the main input converted by the 

mathematical functions, individual characteristics and without 
averaging using the moving window method.
Note: Averaging is not active for the counter type 
measurement modes.

AVG 1

 – the same as 

IND 1

, but averaged using the moving 

window method.

VAL 1

 – 

measuring value on the main input (I1) without 

conversion and without averaging, calculated only by 

CONSt

 

parameter.

EXt 1

 – value additionally measured on the main input (e.g. a 

frequency during the period measurement).

IND 2

 – measuring value on the additional input converted by 

the mathematical functions, individual characteristics and 
without averaging using the moving window method.
Note: Averaging is not active for the counter type 
measurement modes.

AVG 2

 – the same as 

IND 2

, but averaged using the moving 

window method.
VAL 2

 – 

measuring value on the additional input (I2) without 

conversion and without averaging, calculated only by 

CONSt

 

parameter.

EXt 2

 – value additionally measured on the additional input 

(e.g. a frequency during the period measurement).

tIME

 – current RTC time in hh.mmss format.

Note:

 The averaging period is defined by 

MAVG

 setting.

Alarm type (see section 5.4.3)

Default: H-oFF

n-on

 – normally enabled

n-oFF

 – normally disabled

on

 – enabled 

oFF

 – disabled 

H-on

 – permanently enabled (manually)

H-oFF

 – permanently disabled (manually)

REG

 – the state controlled by the MODBUS protocol register.

Alarm state change lower threshold.

Default: 10

-99999…999999

Alarm state change upper threshold.

Default: 20

-99999…999999

Alarm activation delay - the duration in 
seconds of the alarm state before activating 
the alarm relay.

Default: 0

0…900

Alarm deactivation delay - the duration in 
seconds the state without the alarm before 
deactivating the alarm relay.

Default: 10

0…900

Alarm signalization latch. When the function is 
enabled, after the alarm event ends, the 
display indicator informing about the alarm 
status will be flashing signaling the alarm until 
it is canceled by a combination of buttons 

 or via the RS-485 interface.

Default: OFF

ON

 – alarm memory is activated.

OFF

 – alarm memory is deactivated.

Summary of Contents for N32O






































































Reviews:

No comments