Lumel N32O User Manual Download Page 13 | Manualshive

Page: 13 / 69

Lumel N32O User Manual Download Page 13

N32O

User's manual

13

press first the button

, and then the button

and holding them

until DELMIN message is displayed.

Deleting alarm memory - hold down the buttons for 3 seconds. ClrAL message
will be displayed after deleting alarm memory.

STOP – Pressing the buttons combination will stop the active counters,
provided that the permission to control the counter using the meter buttons is
enabled in the input configuration (bCtrl setting). The buttons operation applies
only to the inputs working in the counter mode.

START – Pressing the buttons combination will start the counters, provided that
the permission to control the counter using the meter buttons is enabled in the
input configuration (bCtrl setting). The buttons operation applies only to the
inputs working in the counter mode.

RESET – Pressing the buttons combination will reset (set) the counters,
provided that the permission to control the counter using the meter buttons is
enabled in the input configuration (bCtrl setting). The buttons operation applies
only to the inputs working in the counter mode.

All the events of deleting of saved minimum, maximum values and alarm activation
memory are indicated by the meter by displaying an appropriate message.

5.3 Programming meter parameters

Programming meter parameters is possible via the RS485 interface and by direct edition of
the parameters using the buttons and the meter display.

Direct programming process is easy thanks to meter menu, which includes the settings
grouped into sections with all parameters related to a given functionality, e.g. all
parameters of the serial interface are grouped in the menu

.

Pressing and holding the confirm button for at least 3 seconds allows to switch from a
normal operation to meter menu

. If access to change the parameters is password

protected, the user will be requested to enter the access password before entering the
menu.   Entering   an   incorrect   password   will   allow   to   enter   the   menu   but   it   will   be   not
possible   to   change   the   parameters   -   parameters   monitoring   mode.   Entering   a   correct
password   will   allow   to   move   to   a   programming   matrix,   the   menu   after   entering   the
programming mode is shown below.

Fig. 9: View of meter menu.

«
...
11
12
13
14
15
...
»

Summary of Contents for N32O






































































Reviews:

No comments