Lumberjack YTL-590-111, Instruction Manual

Page: 4 / 25

‐ 4 ‐
GENERAL SAFETY
• ALWAYS keep the operator’s manual in the canister for reference. Review the manual periodically and whenever
questions arise.
• ALWAYS keep all bystanders and pets a minimum of 10 feet away from your work area when operating the log
splitter. Only the operator should be near the log splitter during use.
• NEVER activate the control valve until all people are clear of the work area.
• NEVER wear loose clothing or jewelry when operating the log splitter. Keep clothing and hair away from all moving
parts when operating the log splitter.
• NEVER allow adults without proper instruction and operational knowledge to use the log splitter.
• NEVER operate the log splitter when under the influence of drugs, alcohol or medication or when otherwise not
alert enough to operate the log splitter.
• DO NOT allow children to play on, stand upon, climb on or operate the log splitter at any time.
WORK AREA
• NEVER operate the log splitter on wet, icy, slippery or unstable ground.
• NEVER operate the log splitter in an enclosed area. Exhaust fumes
contain the deadly poison carbon monoxide.
• ONLY operate the log splitter with adequate lighting in the work area.
• ONLY operate the log splitter on level ground. Operating on a slope may
cause the log splitter to move and/or logs to
fall off the log splitter.
• ALWAYS keep the work area free of debris. Remove any split wood
around the log splitter immediately to avoid tripping.
PREPARING LOGS FOR THE SPLITTER
Before placing logs on the log splitter, log ends should be cut as squarely as possible. The square shape of the log
helps prevent the logs from moving during splitter operation. The maximum log length is 20 inches.
OPERATION OF THE LOG SPLITTER
• ONLY operate the log splitter from the operator zone as shown in the diagram. Operating the log splitter outside the
operator zone can result in serious injury or death.
• ALWAYS chock the wheels to prevent the log splitter from moving while operating the log splitter.
• ALWAYS know how to stop the log splitter and disengage the controls before operating the log splitter.
• NEVER attempt to split a log against the grain.
• NEVER attempt to split two logs at the same time.
• NEVER step over the log splitter during operation.
• NEVER reach or bend over the log splitter to pick up a log while splitter is in use.
• NEVER attempt to load the log splitter when the wedge is in motion.
• NEVER place hands or feet between the log and splitting wedge during forward or reverse stroke, as this could result
in serious injury or death.
• NEVER use your foot, a rope or any extension device to operate the control lever on the valve. Only use hands to
operate the control levers.
• NEVER touch the muffler and other hot areas of the engine. Allow time for the engine to cool down before touching.
• NEVER move the log splitter while the engine is running.
• NEVER leave the log splitter running unattended, even for a short period of time. Before leaving the log splitter
always turn off the engine.
GENERAL REPAIR
• NEVER operate the log splitter if it is in poor mechanical condition or needs repairs.
• NEVER alter/modify the log splitter as any alterations/modifications may make the log splitter unsafe and void the
warranty.
• NEVER perform any service or repair on the log splitter without first removing the spark plug wire.
• NEVER tamper with the engine settings. The maximum engine speed is preset by the manufacturer and conforms
with safety limits. Refer to the engine owner’s manual for the particular log splitter.
• ALWAYS perform all recommended maintenance procedures before using the log splitter.
• ALWAYS check the level of hydraulic oil and engine oil before operating the log splitter.
• NEVER attempt to remove stuck logs while the log splitter is running.
• ALWAYS replace all damaged or worn parts immediately with parts approved by the manufacturer.
• ALWAYS check regularly that all nuts, bolts, screws, hydraulic fittings and hose clamps are tight.
• ALWAYS be sure any and all replacement parts meet the manufacturer’s specifications.
IMPORTANT SAFETY INFORMATION