background image

 

‐ 14 ‐ 

 

 

 

WARNING 

Read and understand all instructions and safety information in this manual and on safety 
decals before assembling or operating the log splitter. Failure to understand instructions 
and safety information could result in serious injury or death. Do not allow anyone to 
operate the log splitter who has not read this manual. A log splitter can be dangerous if 
assembled or used improperly. Do not operate this log splitter if you have any questions 
concerning safe operation. Call our customer support department at 1-888-723-6534 for 
answers to any questions. 

 

 

WARNING 

ALWAYS 

use the log splitter for its intended use. 

ONLY

 use the log splitter to split wood logs, length wise with the grain. 

NEVER

 modify, alter or change the log splitter in any way. (Modifications will void the warranty.) 

NEVER

 attach a rope, cable or any other device to the control lever on the log splitter. 

ONLY

 operate the log splitter in daylight/adequate lighting. 

NEVER

 leave the log splitter unattended while the engine is running. 

NEVER

 change the splitting position when the engine is running.   

NEVER

 touch the muffler during or immediately after using the log splitter. The muffler becomes 

very hot and can cause serious burns. 

ALWAYS

 make sure the beam is in the locked position. 

DO NOT

 let the beam drop as it may crush fingers or other body parts and/or cause damage to the 

log splitter. 

NEVER

 operate or allow anyone else to operate the log splitter while under the influence of 

alcohol, drugs, or medication. 

 

USING THE LOG SPLITTER   
 

1.  NEVER use the log splitter to carry passengers; never sit upon or stand on the log splitter. 
2.  Before  using  the  log  splitter,  check  the  hydraulic  oil  level  and  visually  inspect  all  the  hoses  and 

attachments for potential problems. 

3.  Inspect the engine and check that the engine oil level is correct. 
4.  Before transporting the log splitter, the hitch accessory must be firmly secured. 

 

TIRE WARNING 

DO NOT use the log splitter if the tires are severely worn and need to be replaced. 
Tires are NOT compatible with towing. 

 

5.  Refer to the vehicle owner’s manual for proper safety and transport instructions. 

 

TRANSPORT WARNING 

Serious injury or death can occur if transportation safety rules are not followed. 
Always secure and lock the log splitter to the transporting vehicle before moving. 
Drive safely when transporting the log splitter. Be aware of the added length of the log splitter. 
Never exceed the maximum travel speed of 10 mph. 
Never ride upon or transport any cargo on the log splitter. 
Turn off the transporting vehicle before leaving the log splitter unattended. 
Block the log splitter wheels to prevent unintended movement during transport. 

OPERATING INSTRUCTIONS 

Summary of Contents for YTL-590-111


























Reviews: