Lucent Technologies CAJUN P120 User Manual Download Page 98

Page: 98 / 130

Chapter 7

Cajun Campus CLI (Command Line Interface)

Cajun P120 User’s Guide

Examples:

To upload the configuration file:

Console>(enable)

copy running-config tftp C:\P120.cfg

149.49.38.41

IP address of remote host [149.49.38.41]?

Upload configuration to [C:\P120.cfg]?

Output:

Loading configuration please wait……………………………

Configuration has been copied successfully. (12316 bytes)

Console>(enable)

To download the configuration file:

Console>(enable)

copy tftp running-config config1.cfg

149.49.38.41

IP address of remote host [149.49.38.41]? y

Download configuration from [config1.cfg]? y

Configure using config1.cfg from 149.49.38.41 (y/n)? y

Output:

Loading configuration please wait…………………………….

Finished network download. (10067 bytes)

Console>(enable)

Returning to Normal Mode

Disable Command

Use the

disable

command to return to normal mode from privileged mode.

The syntax for this command is:

disable

Example:

Console>(enable) disable

Console>

Downloading a Software Image

Download Command

Use the

download

command to copy a software image from a specified host to the

Flash memory of the Cajun P120.

Summary of Contents for CAJUN P120



































































































































Search results

Summary of Contents for CAJUN P120

Reviews:

Related manuals for CAJUN P120

Brands by name

Popular brands

Lucent Technologies CAJUN P120, User Manual

Search results

Summary of Contents for CAJUN P120

Reviews:

Related manuals for CAJUN P120

Brands by name

Popular brands