Lucent Technologies CAJUN P120 User Manual Download Page 125

Page: 125 / 130

Cajun P120 User’s Guide

111

Download the Software Using TFTP (via the CLI)

Figure B.1

TFTP Software Download Procedure - Overview

Creating the “.lst” file

The “.lst” file is a text file that contains the directory where the Cajun P120
software is located. You will need to enter the name of this file when configuring
the Cajun P120 TFTP parameters.

To create the .lst file, perform the following steps:
1

Create a text file (using an application such as Windows Notepad) containing
the full path to the file name of the .exe file you uncompressed, e.g.,

c:\P120\p120.exe

Save the file with the extension .lst, e.g.,

P120.lst

in the target directory.

Prepare the software files for

download on the TFTP server

Create a "lst" file

Configure the Cajun P120 TFTP

parameters

Download the software

Reset the Cajun P120

Summary of Contents for CAJUN P120



































































































































Search results

Summary of Contents for CAJUN P120

Reviews:

Related manuals for CAJUN P120

Brands by name

Popular brands

Lucent Technologies CAJUN P120, User Manual

Search results

Summary of Contents for CAJUN P120

Reviews:

Related manuals for CAJUN P120

Brands by name

Popular brands