background image

Safety Instruction 

These instructions are intended to ensure that user can 
use the product correctly to avoid danger or property 

loss. 
The precaution measure is divided into “Warnings” and

 

“Cautions”.

 

Warnings: Serious injury or death may occur if any of

 

the warnings are neglected.

 

Cautions: Injury or equipment damage may occur if any

 

of the cautions are neglected.

 

Warnings Follow 

Cautions Follow these 

these safeguards to 

precautions to prevent 

prevent serious injury 

potential injury or 

or death. 

material damage. 

Warnings 

In the use of the device, you must be in strict 
compliance with the electrical safety regulations of 

the nation and region. 

Input voltage should meet both the SELV (Safety Extra 
Low Voltage) and the Limited Power Source with 12 

VDC according to the IEC60950-1 standard. Refer to 

technical specifications for detailed information. 

Do not connect multiple devices to one power 
adapter to avoid over-heating or a fire hazard caused 

by overload. 

Make sure that the plug is firmly connected to the 
power socket. 

Make sure that the device is firmly fixed if wall 
mounting or ceiling mounting is adopted. 

If smoke, odor or noise rise from the device, turn off 

the power at once and unplug the power cord, and 
then contact the service center. 

Never attempt to disassemble the camera by 

unprofessional personal. 

Cautions 

Do not drop the camera or subject it to physical 

shock. 

Do not touch senor modules with fingers. 

If cleaning is necessary, use clean cloth with a bit of 

ethanol and wipe it gently. 

Do not aim the camera at the sun or extra bright 
places. 

The sensor may be burned out by a laser beam, so 
when any laser equipment is in using, make sure that 
the surface of sensor will not be exposed to the laser 

beam. 

Do not expose the device to high electromagnetic 
radiation or extremely hot, cold, dusty or damp 

environment. 

To avoid heat accumulation, good ventilation is 
required for the operating environment. 

Keep the camera away from liquid while in use for 
non-water-proof device. 

While in delivery, the camera shall be packed in its 

original packing, or packing of the same texture. 

                    Available from A1 Security Cameras 

    www.a1securitycameras.com email: [email protected]

Summary of Contents for CMHT1722WE-28















Reviews: