Doc: I470GB10_16.docx 18/10/2016
p. 13 / 19
Alarm table
COD
DESCRIPTION
Enabled
Reta
in
ed
Gl
ob.
Al
.
M.
Faul
t
Mec.
E.
Faul
t
Elect
.
Siren
Engi
ne
stop
Co
o
lin
g
Motor
R
un
Inhi
bi
t.
No
L
CD
A01
Engine temperature warning (analog sensor)
●
●
●
A02
High engine temperature (analog sensor)
●
●
●
●
●
●
A03
Analog temperature sensor fault
●
●
●
●
●
A04
High engine temperature (digital sensor)
●
●
●
●
●
●
●
A05
Low engine temperature (analog sensor)
●
●
A06
Oil pressure prealarm (analog sensor)
●
●
●
A07
Low oil pressure (analog sensor)
●
●
●
●
●
●
A08
Analog pressure sensor fault
●
●
●
●
A09
Low oil pressure (digital sensor)
●
●
●
●
●
●
●
A10
Digital pressure sensor fault
●
●
●
●
●
A11
Fuel level prealarm (analog sensor)
●
●
A12
Fuel level low (analog sensor)
●
●
A13
Analog level sensor fault
●
●
●
●
A14
Fuel level low (digital sensor)
●
●
●
A15
High battery voltage.
●
●
●
●
●
A16
Low battery voltage
●
●
●
●
●
A17
Inefficient battery
●
●
●
●
●
A18
Battery alternator fault
●
●
●
●
●
●
●
A19
“Pick-up/W” signal fault
●
●
●
●
●
A20
“Pick-up/W” engine speed low
●
●
●
●
●
A21
“Pick-up/W” engine speed high
●
●
●
●
●
●
A22
Starting failed
●
●
●
●
●
●
A23
Emergency stopping
●
●
●
●
●
●
A24
Unexpected stop
●
●
●
●
●
●
A25
Engine stopping failure
●
●
●
●
●
●
A26
Low generator frequency
●
●
●
●
●
●
●
●
A27
High generator frequency
●
●
●
●
●
●
●
A28
Low generator voltage
●
●
●
●
●
●
●
A29
High generator voltage
●
●
●
●
●
●
●
A30
Generator voltages asymmetry
●
●
●
●
●
●
A31
Max. generator current
●
●
●
●
●
●
●
A32
Generator short-circuit
●
●
●
●
●
●
●
A33
Generator external protection intervention
●
●
●
●
●
●
●
A34
Generator power threshold exceeded
●
●
●
●
●
●
●
A35
Generator phase sequence error
●
●
●
●
●
●
A36
Generator contactor anomaly
●
●
●
●
●
A37
Maintenance request
●
●
●
●
A38
System Error
●
A39
Rent hours expired
●
●
●
●
A40
Radiator coolant level low
●
●
●
●
●
●
●
A41
Manual circuit breaker closed
●
●
●
●
●
A42
Manual circuit breaker open
●
●
●
●
●
A46
Cannot change configuration
●
●
●
●
●
A47
Water in fuel
●
●
●
●
●
●
UA1
UA1
UA2
UA2
A38
System error (5V)
Occurs if an internal error occurs in the RGK4...SA controller. Contact Technical Support.
A39
Rental time finished
Occurs when rental hours reach zero. Use the Commands menu to reset rental hours and reset the alarm.
A40
Radiator coolant low.
Occurs if the coolant level falls below the minimum.
A41
Manual breaker closed.
Occurs during local engine starting if the state of the input programmed as
Breaker state alarm
is detected as
inactive.
A42
Manual breaker open.
Occurs during remote engine starting or engine starting and running if the state of the input programmed as
Breaker
state alarm
is detected as active.
A46
Configuration change not possible
Occurs if the position of the digital inputs for the 2 selectable configurations has been changed, but the conditions
for implementing the change do not exist (e.g. engine running).
A47
Water in fuel
Occurs if the contact signals the presence of water in the fuel.
UA1
…
UA2
User alarm
The user alarm is generated by the activation of the variable or input assigned to it in menu M18.
Commands menu
CODE COMMAND
ACCESS
LEVEL
DESCRIPTION
C01
Reset maintenance interval
User
Resets the maintenance alarm and resets the maintenance hour count to the set value.
C02
Reset partial engine hour count
User
Resets the engine's partial hour count.
C03
Reset total engine hour count
Advanced
Resets the engine's total hour count.
C04
Set engine hour count
Advanced
Sets the engine's total hour count to a determined value.
C05
Reset rental hour count
Advanced
Reset's the engine's rental hour counter to the set value.