background image

SCRUB SINKS USE & INSTALLATION GUIDE

www logiquip com

|

 

19

 

TIMER OPERATION DISPLAY AND PROGRAMMING

TIME DISPLAY

Accumulates time when the timing start input is active  Timing will not take place when the external or front panel reset is active   

The leftmost digit is the time value legend 

DOWN KEY

When the program input is active the 

Down Key 

is used to scroll through the menu items  After a menu item has been chosen for editing, 

the 

Down Key

 is used to set the value for the currently selected (flashing) digit 

NEXT/RESET KEY

Resets the accumulated time if Front Panel Reset is enabled in Programming Mode  When the program input is active the 

Next/Reset 

Key

 is used to select a menu item for editing (left most digit will begin to flash) and then move to the desired digit to be changed 

PROGRAMMING

Programming parameters can be accessed, when the Program Enable input is active, by pressing the 

Down Key

  To edit a parameter use 

the 

Down Key

 to scroll until the desired parameter appears on the screen  Pressing the 

Next Key

 key will cause the leftmost digit of that 

value to begin to flash  Use the 

Next

 and 

Down Key

 in combination to choose individual digits and change their value 

FRONT PANEL RESET ENABLE

When active (ON) the time value, when being displayed, can be reset by pressing the 

Next/Reset Key

  If set 

to OFF, the time value can only be reset through the remote input 

TIME FORMAT

Sets the units in which the elapsed time will be accumulated  Use the 

Next Key

 to scroll through the  

available choices: Seconds, Minutes (_ _ _ _ _   _), Hours (_ _ _ __   _) , Hours: Minutes: Seconds 

NOTE: On initial start-up, as well as after any programming changes, it is necessary to reset the unit before beginning operation 

MAN-004

18

www.macmedical.com

-ROOT

R

  NNeexxtt//RReesseett  KKeeyy

345678

S

DDoowwnn  KKeeyy  

EAGLE SIGNAL

o n

______

S .

1 .

TTiim

mee  DDiissppllaayy  

MAN-004

18

www.macmedical.com

-ROOT

R

  NNeexxtt//RReesseett  KKeeyy

345678

S

DDoowwnn  KKeeyy  

EAGLE SIGNAL

o n

______

S .

1 .

TTiim

mee  DDiissppllaayy  

MAN-004

18

www.macmedical.com

-ROOT

R

  NNeexxtt//RReesseett  KKeeyy

345678

S

DDoowwnn  KKeeyy  

EAGLE SIGNAL

o n

______

S .

1 .

TTiim

mee  DDiissppllaayy  

Summary of Contents for SS32

























Reviews: