Lissmac MAB 2001 Operating Instructions Manual Download Page 38

Page: 38 / 67

38/67

ACCESSORIES

9.1.

Subframes

There is the possibility of increasing the working height of the masonry work platform by using a subframe.

Only subframes of type UG 250 must be used. When using subframes, additionally observe the operating
instructions of the respective subframe!

9.2.

Wheel Set

CAUTION

Unsafe transport

Personnel injury or property damage may result.



Masonry working platform may only be moved if there are no persons or objects on the platform
surface.



Transport may only be done when the masonry working platform is lowered and all railing
elements are removed.

WARNING

Danger of crushing by a masonry platform without an operator

Personnel injury or property damage may result.



Moving the masonry platform on wheels over inclines or declines is prohibited.



Masonry working platform may only be moved if there are no persons or objects on the masonry
working platform.



The wheels may only be used for short stretches and on level concrete surfaces.



Retract all extensions of the masonry work platform.



Attach the wheel set to the receptacles.

The wheel set latches via a safety latch.
To remove the wheel set, you only need to pull the safety latch.

Summary of Contents for MAB 2001




































































Search results

Summary of Contents for MAB 2001

Reviews:

Brands by name

Popular brands

Lissmac MAB 2001, Operating Instructions Manual

Search results

Summary of Contents for MAB 2001

Reviews:

Brands by name

Popular brands